Ferno Ultra Care 4000 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 23

Ferno Ultra Care 4000 Скачать руководство пользователя страница 19

© Ferno-Washington, Inc. 234-2117-01 May 2003

19

Ultra Care 4000

™

6 - MAINTAINING THE LIFT

6.1 Maintenance Schedule

The lift requires regular maintenance. Set up and follow
a maintenance schedule. A form is provided on page
23. The following table represents minimum
maintenance.

When using maintenance products, follow the
manufacturers’ directions and read the manufacturers’
material safety data sheets.

In the U.S.A., contact Ferno Customer Relations to
order Ferno disinfectants and cleaners (page 22).

6.2 Disinfecting the Lift

Wipe all surfaces of the lift with disinfectant. Follow
disinfectant manufacturer ’s directions. Ferno
recommends inspecting the lift for obvious damage as
you disinfect it.

•

Each Month

As Needed

Each Use

Disinfecting

(this page)

Cleaning

(this page)

Inspecting

(page 20)

•

•

•

Improper maintenance can cause injury.
Maintain the lift only as described in this
manual.

WARNING

!

6.3 Cleaning the Lift

Remove the straps and follow the instructions in

Disinfecting and Cleaning the Straps

below.

Clean all surfaces of the lift with a damp, soft cloth
and a mild detergent. Use a stiff-bristled brush (but not
a metal wire brush) if necessary. Rinse by wiping with
a clean, damp cloth. Dry the lift with a towel.

Maintaining the Lift

6.4 Disinfecting and Cleaning

the Straps

1. Remove the straps from the lift.

2. Spray metal slides with a disinfectant cleaner and

wipe with a clean cloth, following disinfectant
manufacturer’s instructions. Do

not

immerse

metal slides in liquid.

3. Add a disinfectant cleaner to warm water,

following the disinfectant manufacturer ’s
instructions.

4. Grasp the metal slides and immerse strap

webbing in the disinfectant solution for the
contact time directed by the disinfectant
manufacturer. Do

not

immerse metal slides.

5. To rinse, grasp the metal slide and repeatedly dip

the strap webbing in clear water. Do

not

immerse

the metal slides.

6. Hang straps to air dry.

Important

Metal slides on straps can be damaged by
immersion in liquids or by washing machine
action. Disinfect and clean straps only as
directed in this manual.

«
...
17
18
19
20
21
...
»

Содержание Ultra Care 4000
























Отзывы:

Нет отзывов