Fenix Imvico TK41 Скачать руководство пользователя страница 34

Страница: 34 / 88

FENIX IMVICO

TK-41 OPERATION MANUAL

34/88

3.3.1.- BUTTONS FUNCTIONS

1) PFEED Button.

Functions:

•

If pressed on start-up, it activates the

SELF-TEST MODE.

•

If pressed together with PROG button on start-up, they activate the

HEXADECIMAL MODE

•

During

PROGRAMMING MODE

this is the

“YES”

button.

•

If pressed when the printer is already started, its function depends on

whether the OM (Optical Mark ) sensor is enabled or not.

•

When the OM (Optical Mark) sensor is disabled, the printer feeds

paper continuously while pressing the PFEED button.

•

When the OM sensor is enabled, the printer will feed paper by mark

paper unit.

•

Paper feeding using the paper FEED button cannot be performed under the

following conditions:

•

The paper roll end sensor detects a paper end.

•

When the printer thermal head is open.

2) PROG Button.

Functions:

•

If pressed on start-up, it activates the

PROGRAMMING MODE

•

If pressed together with PFEED button on start-up, they activate the

HEXADECIMAL DUMP MODE

•

During

PROGRAMMING MODE

this is the

“NO”

button.

•

If pressed when the printer is already started, this button does nothing.

NOTE

: See

3.4- SPECIAL MODES

for explanations on

SELF-TEST MODE

PROGRAMMING MODE

and

HEXADECIMAL DUMP MODE

Содержание TK41

























































































Результаты поиска

Содержание TK41

Отзывы:

Похожие инструкции для TK41

Бренды по названию

Популярные бренды

Fenix Imvico TK41, Руководство по эксплуатации

Результаты поиска

Содержание TK41

Отзывы:

Похожие инструкции для TK41

Бренды по названию

Популярные бренды