![background image](http://html1.mh-extra.com/html/femi/842/842_instructions-for-use-and-maintenance-manual_4015912017.webp)
14
(1
- Remove the external flange
, remove the blade by
sliding it out from the lower part of the head and install
a new blade.
- Ensure that the blade’s teeth are oriented in the
direction of the arrow on the blade itself.
- Then, remount the outer flange
, tighten the screw
firmly, using the Allen wrenches supplied.
127( 7KH PRYDEOH JXDUG ZLOO UHWXUQ WR
WKH FRUUHFW SRVLWLRQ DXWRPDWLFDOO\ ZKHQ WKH
PDFKLQHKHDGLVORZHUHGZLWKRXWKDYLQJWR
UHSRVLWLRQWKHSDZO
:$51,1*1HYHULQVWDOOEODGHVZKLFKDSSHDU
WR EH FUDFNHG 2QO\ LQVWDOO EODGHV ZKLFK
FRPSO\ZLWKVWDQGDUG(1
&877,1*&$3$&,7<)LJ
The following tables specifies the cutting capacity at 0°
and 45° which may be achieved under the normal
conditions of use illustrated in this manual.
9(56,21
9(56,21
$&&(6625,(6
6(/(&7,212)7+(%/$'(
7KH PLWUHVDZ LV ILWWHG ZLWK D :,',$ EODGH
GLDPHWHU[KROHLQYHUVLRQGLDPHWHU[
LQYHUVLRQ
&/$036)LJ237,21$/
&$87,21:KHQ FXWWLQJ EDUV RU SLHFHV RI
DOXPLQLXP RU SODVWLF XVH RI WKH FODPS LV
DGYLVDEOHWRKROGWKHSLHFHILUPO\DJDLQVWWKH
DQJXODU EHDULQJV WKXV DYRLGLQJ PRYHPHQW
GXULQJ FXWWLQJ DQG WKHUHIRUH MDPV ZKLFK
FRXOG GDPDJH ERWK WKH ZRUN SLHFH DQG WKH
EODGH
Always check that the clamp jaw makes perfect contact
with the piece to be cut and that it effectively holds it in
position at the base.
68&7,21 2) '867 5(6,'8(6 )LJ
237,21$/
The mitre-saw can be connected to an aspirator or a
dust collection bag can be mounted by means of the
exhaust manifold
.
The aspirator pipe or the bag sleeve must be secured to
the manifold by means of a band. Users are reminded to
empty the bag or aspirator container and to clean the
filter regularly.
The air output speed must be equivalent to at least
100Nm
3
/h.
For example, "dustbin" type aspirators are suitable.
0$,17(1$1&(
5287,1(0$,17(1$1&(
The regular maintenance described above and in the
paragraph below can be carried out by unskilled
personnel.
1. Do not oil the mitre-saw; cutting must be carried out
in dry conditions (including the cutting of aluminium
and aluminium alloys); all rotating parts are self-
lubricating.
2. During maintenance, wear protective gear if possible
(accident-prevention goggles and gloves).
3. Remove cuttings when necessary both from the
cutting area, work surfaces and support bases.
Use of an aspirator or brush is recommended.
:$51,1*'RQRWXVHFRPSUHVVHGDLU
4. Regularly check blade conditions: if difficulties
should arise during cutting, have it sharpened by
skilled personnel or replace it if necessary.