11
(1
/HJHQG)LJ
Control handgrip
Main switch start button
Base
Body/base swivel joint
Rotating bearing
Motor
Blade
Lever to unblock graduation
Button to unblock body descent
Permanent blade shield
Movable blade shield
Bar clamp shaft (optional)
Dust exhaust manifold
Work piece clamps (optional)
Upper work surface
Movable upper safety guard
Bearing bracket
Support feet
Transport locking pin
Main switch locking device
Main switch release device
,167$//$7,21
5(029$/2)3$&.$*,1*
Remove the box used to protect the machine during
transport and keep it intact for future transport and/or
storage.
+$1'/,1*
This mitre-saw is small and light and, therefore, can be
easily handled by one person alone by locking the
transportation block by means of the pin
and by
lifting the machine by means of the control handgrip
.
:$51,1* :KHQ WUDQVSRUWLQJ WKH PDFKLQH
WKHXSSHUSDUWRIWKHEODGHPXVWEHFRYHUHG
$OZD\V FKHFN WKDW WKH EODGH LV SURWHFWHG E\
WKHUHODWLYHXSSHUJXDUG
75$163257$7,21
To transport the machine, place it in the box it was in
when purchased. Ensure it is placed in the correct
position indicated by the arrows on the packaging.
Pay careful attention to the ideograms printed on the
box as they provide all necessary information for
palletization and stacking of boxes.
Tying the load down with ropes or safety belts is
recommended during transportation to stop the load
from sliding or falling.
326,7,21:25.67$7,21)LJ
Place the machine on a work bench or on a sufficiently
flat base/pedestal to ensure the best possible stability. -
Should you wish to fix the machine in place, use the
special holes located on the base.
Bearing in mind ergonomic criteria, the ideal height of
the bench or of the base should be such that the base
surface or the upper work surface is between 90 and 95
cm. from the ground
VHHILJ
.
Always ensure that there is at least 80 cm. of
manoeuvring space in all directions around the machine
in order to perform all necessary cleaning, maintenance
and adjustment operations safely with a sufficient
amount of space available
VHHILJ
.
&$87,21 (QVXUH WKH PDFKLQH LV SODFHG LQ D
VXLWDEOH
SRVLWLRQ
ERWK
LQ
WHUPV
RI
HQYLURQPHQWDOFRQGLWLRQVDQGOLJKWLQJ
$OZD\VEHDULQPLQGWKDWJHQHUDOHQYLURQPHQWDO
FRQGLWLRQV DUH RI IXQGDPHQWDO LPSRUWDQFH WR
SUHYHQWDFFLGHQWV
(/(&75,&$/&211(&7,216
Check that the electrical system to which the machine is
connected is earthed in compliance with current safety
regulations and that the current socket is in perfect
condition.
The electrical system must be fitted with a
magnetothermal protective device to safeguard all
conductors from short circuits and overload.
The selection of this device should be in line with the
following electrical specifications of the machine stated
on the motor.
127( <RXU PLWUHVDZ¶V HOHFWULFDO V\VWHP LV
HTXLSSHG ZLWK DQ XQGHUYROWDJH UHOD\ ZKLFK
DXWRPDWLFDOO\ RSHQV WKH FLUFXLW ZKHQ WKH
YROWDJH IDOOV EHORZ D PLQLPXP SUH
HVWDEOLVKHGOLPLWDQGZKLFKSUHYHQWVWKHVHOI
UHVHW RI PDFKLQH IXQFWLRQV ZKHQ YROWDJH
UHWXUQVWRQRUPDOOHYHOV
,I WKH PDFKLQH VWRSV LQYROXQWDULO\ GR QRW EH
DODUPHG0DNHVXUHWKDWWKHUHKDVQRWEHHQD
YROWDJHIDLOXUHLQWKHHOHFWULFDOV\VWHP