background image

13.  Do not open the unit, the power adaptor, or try to modify them in any 

way. There are no user-serviceable parts inside the unit or power 

supply. Opening the unit or power supply, or carrying out any 
modifications will invalidate your warranty, as well as being potentially 
dangerous. Always contact your supplier or the manufacturer for 
service requirements. 

14.  When you are not using the unit for a long period of time, disconnect 

the power adaptor from the wall socket. 

15. Should a problem occur, please read the 

Troubleshooting

 section 

covering common operating errors before deciding the unit is faulty. 

 

 

 

This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference 

in a residential installation. 

This equipment generates, uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no 

guarantee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more of 

the following measures: 

• 

Reorient or relocate the receiving antenna 

• 

Increase the separation between the equipment and AV amplifier 

• 

Connect the equipment to an outlet on a circuit different from that to 

which the AV amplifier is connected 

• 

Consult the dealer or an experienced radio/TV technician for help 

 

 

 

  This unit is in conformity with the EMC directive and 

low-voltage directive. 

 

 

Содержание DD540

















Отзывы: