When the machine is in a tilted position or working on
uneven corners, the FT1030 model will route material
panels up to the depth allowed by the built-in shav-
ing/splinter guard. Use a router bit with a suitable ball
bearing pilot to guide the router.
PRECAUTION:
Do not tighten clip fixing nut
D
without a
milling head inserted into the clip.
ACCESSORIES
Accessories and their corresponding order number can
be found in our catalogues.
MAINTENANCE AND CARE
WARNING!
Always unplug the machine before carrying
out work on it.
Warning!
Type Y attachment. If the supply cord is
damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to
avoid a hazard.
-
Inspect the mounting screws:
Regularly inspect all
the mounting screws and ensure they are firmly tight-
ened. Should any screw be loose, tighten it immediate-
ly. Failure to do so could put you at serious risk.
-
Motor maintenance:
Always take the greatest care
over this and make sure that the motor winding is not
damaged and does not become wet with oil or water.
-
The vents should always be kept clean and free of
obstacles.
-
Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
-
Check that the mains lead is in good condition. If it is not,
take it to an Official Service Centre to have it replaced.
-
Brush replacement:
The brushes should be replaced
after 150 - 200 hours use or when they are less than
10 mm long. Have this done by an Official Service
Centre. We recommend that at every second change
of brushes, you take the machine to one of our Official
Service Centres for general cleaning and oiling.
-
Use only
Felisatti
accessories and spares. Parts
the changing of which is not covered in this instruc-
tion manual, should be replaced in a
Felisatti
Offi-
cial Service Centre.
WARRANTY
See general warranty conditions printed on the at-
tached sheet.
NOISE AND VIBRATION
This tool has been designed and made to reduce noise
to a minimum. However, in spite of this,
in certain
circumstances the maximum noise level in the place
of work could exceed 85 dBA. In this case, the oper-
ator should wear ear protection.
The machine's noise and vibration levels, measured in
compliance with EN60745-1, usually reach:
Acoustic pressure = 85 dB(A)
Sound-power level = 98 dB(A)
Use ear protection!
Vibration acceleration = 2.5 m/s
2
WARNING!
The vibration level given in these instruc-
tions has been measured in accordance with a standar-
dized measurement procedure specified in EN60745
and can be used to compare devices. Different uses of
the device give rise to different vibration levels and in
many cases they may exceed the values given in these
instructions. It is easy to underestimate the vibration
load if the electrical power tool is used regularly in
particular circumstances.
Note:
if you wish to make an accurate assessment of
the vibration loads experienced during a particular
period of working , you should also take into account the
in-tervening periods of time when the device is switched
off or is running but is not actually in use. This can result
in a much lower vibration load over the whole of the
period of working.
Do not dispose of electric tools in
the household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances and
its translation into national law, used electric tools must
be collected separately and recycled in an ecologically
desirable way.
DECLARATION OF CONFORMITY
Business name of the manufacturer:
INTERSKOL POWER TOOLS S.L.
Full address of the manufacturer:
Crta. de Sant Joan de les Abadesses, s/n 17500
RIPOLL-(Girona) SPAIN
Name and address of the person (established in
the Community) who compiled the technical file:
Jordi Carbonell and Santiago López
Ctra. de Sant Joan de les Abadesses, s/n 17500
RIPOLL-(Girona) SPAIN
Product name:
Router/tilting trimmer
Commercial name:
Router/tilting trimmer
Model:
RF30/750A
Type: Electric power tools
Serial Number: see label of the tool
Fulfils all the relevant provisions of Directives
2006//95/EC, 2006/42/EC, 2004/108/EC,
2002/96/EC, 2002/95/EC, 2009/251/EC
We hereby declare, under our sole responsibility,
that the
FELISATTI
brand products described in
this manual
RF30/750A
comply with the following
standards or standard documents: EN60745-1,
EN60745-2-3, EN55014-1, EN55014-2, EN61000-
3-2, EN61000-3-3.
13
Jordi Carbonell
Plant Mgr.
Santiago López
Marketing Mgr.
We reserve the right to make technical changes 04/2013
