Original instructions
TECHNICAL DATA
Router/tilting trimmer
RF30/750A
Input power
W
750
No-load speed
rpm
27000
Clip diameter
mm
8
Approx. weight (without acces.)
kg
1.9
Read the operating instructions
Protection category II power tool; double
insulated
In accordance with essential applicable
safety standards of European directives
In accordance with essential applicable
safety standards of Russian Federation
Wear eye protection
Wear ear protection
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual.
Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
C Start-up switch (Fig.1)
D Clamping nut (Fig.1)
EQUIPMENT
-
Clip,
∅
1/8”
-
Clip,
∅
8 mm
-
Fixed spanner 13 mm
-
Fixed spanner 17 mm
-
Operating instructions
-
Safety instructions
-
Warranty
SAFETY INSTRUCTIONS
•
See
“Safety Instructions”
manual, supplied with this
instruction manual.
•
For your personal safety, always connect the machine
to a mains supply protected by a differential and ther-
mal cutout switch, in accordance with regulations on
low-voltage wiring sitemaps.
•
Do not pierce the motor housing as this could damage
the double insulation (use adhesive labels).
•
Always unplug the machine before carrying out work on it.
•
Always stop the machine by switching it off, not by
unplugging it.
•
WARNING!
Before each use, inspect the plug and
lead. Should they need replacing, have this done by an
official service centre.
•
Always keep the mains lead clear of the working range
of the machine.
•
Only plug the machine in when it is switched off.
•
Hold the machine firmly in both hands and in a stable
position.
•
When working with the machine, always wear safety
goggles and ear protection. Other personal protection
equipment such as dust masks, gloves, helmet and
apron should be worn when necessary, along with non-
slip safety footwear. A dust mask is required when the
dust from the material deburred, such as paint or other
coating, is harmful. If in doubt, use safety equipment.
•
Make sure the vents are free when working with dust. If
they require cleaning, first unplug the machine, do not
use metal objects and avoid damaging internal parts.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is
correct: it must be the same as that on the specifica-
tion label.
STARTING THE TOOL
Plug the machine in with the switch off.
Start the machine by turning the switch to position 1
("ON"). To switch off, do the same in reverse.
Fitting to the power tool (Mod. 90004.0000)
Remove the collet and the nut from the spindle of the
tool. Remove the 8 mm collet and fit the
⅛
" one, fit the
⅛
" bit and tighten the nut to fasten it. Fit accessory by
loosening set-screw
A
and fitting it in the collar of the
tool. Then tighten set-screw
A
to secure it.
PRECAUTION:
Do not tighten clip fixing nut
D
without a
milling head inserted into the clip.
DEPTH ADJUSTMENT (Mod. 900
04
.0000)
With the accessory securely fitted to the tool and the bit
in place, loosen the regulator set-screw
B
, and move up
and down until the required depth is obtained. Tighten
the regulator set-screw
B
to secure.
Warning:
Bits should be specially cut for plaster or PVC.
DEPTH ADJUSTMENT (Mod. FT1030)
With the motor firmly secured in the locking ring and the
router bit installed, use a screwdriver to loosen the depth
set-screw
B
by approximately 1/4 turn.
Raise or lower the base by turning the grooved gear and
retighten the screw at the desired position.
Model FT1030 has an angular adjustment range of 75
degrees (45 degrees in one direction and 30 in the
other). To adjust the angle, loosen the wing nuts
E
on
the sides of the base. Tilt the motor to the desired angle
and retighten the wing nuts.
Do not tighten too much as the base could be damaged!