Fein ASCD12-100W4 Series Скачать руководство пользователя

Страница: 21 / 186

Beware of any concealed electric cables, gas or water
conduits.

Check the working area before commencing

work, e. g. with a metal detector.

Use ear protection during operation.

Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. Where appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments.

The eye

protection must be capable of stopping flying debris
generated by various operations. The dust mask or res-
pirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high inten-
sity noise may cause hearing loss.

Secure the work piece firmly.

A work piece that is

gripped tightly in a clamping device or vice, is more
secure than if held by hand.

Hold the power tool firmly.

High reaction torque can

briefly occur.

Do not work materials containing magnesium.

Danger

of fire.

Do not work CFP (carbon-fiber-reinforced polymer) and
materials containing asbestos.

These materials are con-

sidered carcinogenic.

Do not rivet or screw any name-plates or signs onto the
power tool.

If the insulation is damaged, protection

against an electric shock will be ineffective. Adhesive
labels are recommended.

Do not use accessories which are not specifically
designed and recommended by the power tool manu-
facturer.

Safe operation is not ensured merely because

an accessory fits your power tool.

Clean the ventilation openings on the power tool at reg-
ular intervals using non-metal tools.

The blower of the

motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.

Never look or stare into the light of the power tool’s
lamp from a short distance. Never point the light of the
lamp into the eyes of other persons in close vicinity.

The radiation produced by the lamp can be harmful for
the eye.

Do not direct the power tool against yourself, other per-
sons or animals.

Danger of injury from sharp or hot

application tools.

Switch the power tool off immediately when the appli-
cation tool blocks. Do not switch the power tool on
again while the application tool is blocked; this could
lead to kickback with high reaction torque. Determine
and correct the cause of the blockage of the application
tool, taking the safety warnings into account.

Possible

causes could be:

–

Jamming in the workpiece

–

Breaking through the material being worked

–

Overloading the power tool.

Use and handling of the battery (battery pack).

To avoid hazardous situations such as burns, fire,
explosion, skin injuries, and other injuries when han-
dling the battery, observe the following instructions:

Batteries must not be disassembled, opened or reduced
in size. Do not subject batteries to mechanical impact
or shock.

Hazardous vapours and fluid can escape in

case of damage and improper use of the battery. The
vapours can irritate the respiratory system. Liquid
ejected from the battery may cause skin irritations or
burns.

When battery fluid from a damaged battery has come
into contact with objects close by, check the respective
components, clean them or replace them as required.

Keep the battery away from heat and fire. Do not store
the battery in direct sunlight.

Do not remove the battery from its original packaging
until it is going to be used.

Before any work on the machine itself, remove the bat-
tery from the power tool.

If the power tool accidentally

starts, there is danger of injury.

Mount the battery only when the power tool is switched
off.

Remove the battery only when the power tool is
switched off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture
and water.

Clean contaminated battery terminals and

power tool connections with a dry, clean cloth.

Use only intact original FEIN batteries that are intended
for your power tool.

When working with and charging

incorrect, damaged, repaired or reconditioned batter-
ies, imitations or other brands, there is danger of fire
and/or explosion.

Follow the safety warnings in the operating instructions
of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information
sheet has been measured in accordance with a stand-
ardised test given in EN 62841 and may be used to
compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may
differ. This may significantly increase the exposure level
over the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the oper-
ator from the effects of vibration such as: maintain the
tool and the accessories, keep the hands warm, organi-
sation of work patterns.