Fein ABAS18-63AS, Руководство пользователя, Страница: 16 / 228

and noise emission value may differ. This may
significantly increase the vibration and noise
emissions over the total working period.
To estimate vibration and noise emissions accur-
ately, the times when the tool is switched off or
when it is running but not actually being used
should also be taken into account. This may sig-
nificantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect
the operator from the effects of vibration, such
as servicing the power tool and application tools,
keeping their hands warm, and organising work-
flows correctly.
Rechargeable battery
English
Charging the battery
English
u
Use only the chargers listed in the technical
data.
Only these chargers are matched to the
lithium-ion battery of your power tool.
Note: Lithium-ion rechargeable batteries are
supplied partially charged according to interna-
tional transport regulations. To ensure full re-
chargeable battery capacity, fully charge the re-
chargeable battery before using your tool for the
first time.
Inserting the Battery
English
Push the charged battery into the battery holder
until it clicks into place.
Removing the Battery
English
To remove the rechargeable battery, press the
battery release button and pull the battery out.
Do not use force to do this.
The rechargeable battery has two locking levels
to prevent the battery from falling out if the bat-
tery release button is pressed unintentionally.
The rechargeable battery is held in place by a
spring when fitted in the power tool.
Battery charge indicator
English
The green LEDs on the battery charge indicator
indicate the state of charge of the battery. For
safety reasons, it is only possible to check the
state of charge when the power tool is not in op-
eration.
Press the button for the battery charge indic-
ator or
to show the state of charge. This is
also possible when the battery is removed.
If no LED lights up after pressing the button for
the battery charge indicator, then the battery is
defective and must be replaced.
Battery model GBA 18V...
English
LED Capacity
3× continuous green light 60–100 %
2× continuous green light 30–60 %
1× continuous green light 5–30 %
1× flashing green light 0–5 %
Battery model ProCORE18V...
English
LED Capacity
5 × continuous green light 80–100 %
4 × continuous green light 60–80 %
3 × continuous green light 40–60 %
2 × continuous green light 20–40 %
1 × continuous green light 5–20 %
1 × flashing green light 0–5 %
Recommendations for Optimal Handling
of the Battery
English
Protect the battery against moisture and water.
Only store the battery within a temperature
range of −20 to 50 °C. Do not leave the battery in
your car in the summer, for example.
Occasionally clean the ventilation slots on the
battery using a soft brush that is clean and dry.
A significantly reduced operating time after char-
ging indicates that the battery has deteriorated
and must be replaced.
Follow the instructions on correct disposal.
Assembly
English
u
Remove the battery from the power tool
before carrying out work on the power tool
(e.g. maintenance, changing tool, etc.). The
battery should also be removed for trans-
port and storage.
There is risk of injury from
unintentionally pressing the on/off switch.
Inserting/replacing the bandsaw blade
English
u
Always wear protective gloves when
mounting the bandsaw blade.
Danger of in-
jury when touching the bandsaw blade.
u
Always wear safety goggles. Safety goggles
reduce the risk of injury.
Fitting the bandsaw blade (see figures A–E)
English
Release the two locking clips (4)
❶
and lift up the
cover (13)
❷
. Swivel the lever (9) by 180° in rota-
tional direction as far as it will go.
16
en
1 609 92A 7RX • 15.11.22 • T