background image

Model 121ALED and 121ALED-N

Vitalite

®

 LED Rotating Light

 

Limited Warranty

This product’s limited warranty  

can be found at www.fedsig.com/SSG-Warranty.

Safety Messages to Installers and Users 

Products should be installed to code by a licensed electrician 

and follow all safety instructions. Failure to do so may result in property damage, serious injury, or death.
•  Read and understand instructions before installing or operating equipment.
•  To avoid electrical shock hazards, do not connect wires when power is applied.
•  To be an effective warning device, this product produces bright light that could be hazardous to eyesight. 

The possibility exists that rapid flashing lights could induce photosensitive epilepsy. Do not stare directly at 

the light.

Overview: 

Models 121ALED and 121ALED-N rotating LED warning lights are designed for mounting on a flat 

(horizontal or vertical) surface or on a 1/2” NPT threaded pipe. Units are available in 24VDC. 

Certifications and Ratings:

•  UL and cUL Listed
•  Type 4X, IP66 enclosure. Indoor/Outdoor Use
•  IP69K Compliant
•  Model 121ALED-N is NSF Certified 

(dome-up)

 for  

Splash Zones and Non-food Zones to  

NSF/ANSI 2: Food Equipment

•  Electrical ratings: 

024VDC, 0.3A

•  Certified operating temperature:  

-40°F to 150°F (-40°C to 66°C)

Installation:

Unpacking the Device: 

After unpacking the device, examine it 

for damage and verify parts. Unit comes with: (1) 121ALED or 

121ALED-N assembled unit with flying leads, (1) panel mount 

gasket, and (3) # 8-32 panel mounting tapping screws. If a part is 

missing or damaged do not install. Contact Federal Signal Customer 

Support at +1 708-534-4756 or [email protected].

Electrical Connections 

To avoid electrical shock, do not 

connect wires when circuits are energized. Use 18AWG field wiring 

or larger.

•  24VDC Models: 

Connect the positive (+) power source lead to 

the red wire and connect the negative (-) power source lead to 

the black wire.

Mounting the device: 

Units come standard to mount on a flat 

(horizontal or vertical) surface or a 1/2" NPT pipe. Model 121ALED-N 

(NSF Certified) must be mounted in a dome up position to resist 

water and debris accumulation and maintain the NSF Certification. 

Wall or corner mounting accessories are sold separately. 

•  Pipe Mounting  –  

On a 1/2" NPT Pipe, feed wires through pipe 

and turn clockwise to tighten. Recommended tightening torque is 5-ft-lbs (6.8 N-m).

•  Surface/Panel Mounting  –  

Using provided gasket as template, mark three mounting holes and center 

hole for wiring. Drill or punch 3/16" (4.8mm) diameter holes for mounting and a 1" (25.4mm) for wiring. Set 

base on gasket, feed wires through center, and attach to the mounting surface using provided #8 tapping 

screws from the underside.

Installation and Maintenance Instructions

121ALED and 

121ALED-N 

Beacon

Junction box 

(not supplied)

1/2" conduit 

(not supplied)

Wiring

Wiring 

(red wire to 

positive (+)
Power source 

and black wire

To negative (-) 

power source).

1/2" NPT 

Pipe Mount

5.12"/ 130 mm

6.26"/ 159 mm

LED Lamp

Parabolic 

Reflector

Elliptical Dome

(12" Curvature

 Radius) 

Screw

in Base

Содержание Vitalite 121ALED







Отзывы: