Federal Signal Corporation IMPAXX Series Скачать руководство пользователя страница 18

Getting Technical Support and Service

18    

IMPAXX

®

 LED Light Heads 

Federal Signal

 www.fedsig.com

Testing the System

SOUND HAZARD: All effective sirens and horns produce loud 

sounds (120 dB) that may cause permanent hearing loss. Always 

minimize your exposure to siren sounds and wear hearing 

protection. Do not sound the siren indoors or in enclosed areas 

where you and others will be exposed to the sound.

LIGHT HAZARD: To be an effective warning device, an emergency 

warning system produces bright light that can be hazardous to your 

eyesight when viewed at a close range. Do not stare directly into 

this lighting product at a close range, or permanent damage to your 

eyesight may occur.

After the installation, test the emergency warning system to ensure 

that it is operating properly. Test all vehicle functions, including 

horn operation, vehicle safety functions, and vehicle lighting 

systems to ensure proper operation. Ensure that the installation 

has not affected the vehicle operation or changed any vehicle 

safety functions or circuits. After testing is complete, provide a 

copy of these instructions to the instructional staff and all operating 

personnel.
Do not test the sound and light system while driving. Operating the 

vehicle warning systems may pose a hazard to the operator and 

other drivers if the systems do not function as expected. Test the 

vehicle in a controlled environment.

Getting Technical Support and Service

For technical support and service, please contact:

Service Department

Federal Signal Corporation

Phone: 1-800-433-9132 

Email: [email protected] 

Содержание IMPAXX Series





















Отзывы: