manualshive.com logo in svg

Federal Signal Corporation I-IP100ACX, Описание, характеристики и руководство по установке

Поделиться
Скачать
Federal Signal Corporation I-IP100ACX Скачать руководство пользователя страница 23

23

Installation

Description, Specifications, and Installation Manual

JP5 - Alarm Initiation Inputs
1 - ISO-GND
2 - Input #1
3 - ISO-GND
4 - Input #2
5 - ISO-GND
6 - Input #3
7 - ISO-GND
8 - Input #4

Ethernet Port

The Informer100 Speaker has an 8 pin Ethernet port for connecting to the network. 

Ethernet wire runs must be less than 328 feet from the nearest network switch. Do not 

install in a conduit carrying high voltage. The wired Ethernet port auto-negotiates a 

10/100, full or half duplex connection.  

Putting the Informer100 Speaker into Standalone Mode

Standalone mode allows the Informer100 Speaker to be activated from the Alarm 

Initiation Inputs without being connected to a network. The Informer100 requires setup 

prior to placing into standalone mode. All configuration should be performed prior to 

installing. Once the unit is configured and tested, place a shorting jumper across pins  

1 and 2 of JP3. To configure the Informer100 Speaker, use Commander software version 

14.9.0 or later. See the 

Informer Setup and Programming Manual

.

Relay Outputs 

The Informer100 Speaker has two independently programmable relay outputs. The relay 

timing is configured and programmed into the Informer100 Speaker from the Commander 

user interface.
The relay outputs are capable of controlling external devices. The normally outputs 

are located at pins 1 & 2 and pins 3 & 4 of the removable output connector JP4 on the 

controller board. The outputs can be wired in series with the power wired into the unit 

by using the power connections available on JP6 and JP7, providing switched AC or DC 

power to activate other devices.
Do not exceed the voltage and current ratings listed in the specifications section of this 

manual. When using this feature, the relay outputs turn on until one of the following 

occurs:
•  Until the programmed default timeout occurs
•  Until the CANCEL or RESET command is received
You can individually configure the relay outputs to open, close, and cycle based on a pre-

programmed sequence. Relays can also be configured to turn on when PA VOIP is active. 

Содержание I-IP100ACX

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды