manualshive.com logo in svg

Federal Signal Corporation I-IP100ACX, Описание, характеристики и руководство по установке

Поделиться
Скачать
Federal Signal Corporation I-IP100ACX Скачать руководство пользователя страница 11

11

Specifications

Description, Specifications, and Installation Manual

The following indicators are for troubleshooting purposes only. These indicators are not 

visible when the unit is closed.

Table 2 Visual Indications (Located on internal control board.)

POWER 

Green LED turns on when power is connected. D5

ISOLATED POWER Green LED turns on when Isolated power for inputs and relay 

outputs is functioning. D6

CPU

Flashing RED LED indicates the CPU is running its program. D18

NETWORK

Green LED turns on when unit has made a connection to the 

network. D27

LISTEN

Red LED turns on when Commander is listening. Unit is sending 

audio to Commander. D25

TALK 

Green LED turns on when Commander is talking. Unit is playing 

audio being sent. D26

AMPOUTPUT 

VOLTAGE

Green LED turns on when amplifier is active. Brightness indicates 

level of amplifier output. D2

AMPLIFIER 

OUTPUT 

CURRENT

Green LED turns on when amplifier is active. Brightness indicates 

level of amplifier output. D8

ACTIVATION 

INPUT #1

Red LED turns on when Activation input #1 is being activated. D12

ACTIVATION 

INPUT #2

Red LED turns on when Activation input #2 is being activated. D14

ACTIVATION 

INPUT #3

Red LED turns on when Activation input #3 is being activated. D16

ACTIVATION 

INPUT #4

Red LED turns on when Activation input #4 is being activated. D17

Table 3 Connectors and Jacks (Control board connectors)

JP2 

Serial Port for factory approved programming or for message board 

display

JP3 Pin Jack

Short pins 1 and 2 for standalone mode

JP4 Relay Outputs

1 and 2 Relay 1 Normally Open

3 and 4 Relay 2 Normally Open

JP5 Initiation inputs 1 and 2 – ISO Ground/Input 1

3 and 4 – ISO Ground/Input 2

5 and 6 – ISO Ground/Input 3

7 and 8 – ISO Ground/Input 4
NOTE: JP6, JP7, JP8 and JP9 are physically connected to provide 

a distribution of AC or DC power. The combined load of all power 

should not exceed 8 amperes AC/DC, 25 A max inrush

JP6 and JP7

AC/DC Power 

Distribution

1 – L1/Hot/(+) 24 Vdc

2 – L2/Neutral/(-) 24 Vdc Gnd

3 – Earth Ground 

JP8

Input for AC/DC 

Power Distribution

1 – L1/Hot/(+) 24 Vdc

2 – L2/Neutral/(-) 24 Vdc Gnd

3 – Earth Ground

Содержание I-IP100ACX

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды