Fayat Group Bomag BVT 65 Скачать руководство пользователя страница 87

Страница: 87 / 97

9.2 Engine malfunctions

Malfunction

Possible cause

Remedy

Engine does not

start

Fuel tank empty

Check, fill up if necessary

Fuel system clogged

Clean the fuel screen in the tank

Replacing the fuel filter

Check the fuel screen in the carburettor

Have checked by qualified expert per-

sonnel

Set the engine stop switch to position

"OFF"

Set the engine stop switch to position

"ON"

Engine oil level too low

(The engine oil level warning lamp lights)

Check the engine oil level, correct if nec-

essary

No ignition spark

Clean the spark plug, replace if neces-

sary

Check the ignition coil

Have checked by qualified expert per-

sonnel

Engine stop switch defective

Have checked by qualified expert per-

sonnel

No fuel in carburettor

Check the fuel supply

Have checked by qualified expert per-

sonnel

Engine does not

crank when oper-

ating the recoil

starter

Recoil starter defective

Replace the recoil starter

Spring broken

Replace the recoil starter

Starter rope of

recoil starter does

not return to initial

position

Recoil starter dirty

Clean the recoil starter

Insufficient pre-tension of the spring

Check the pre-tension of the spring,

adjust if necessary

Spring broken

Replace the recoil starter

Engine stops fre-

quently in short

intervals

Fuel system clogged

Clean the fuel screen in the tank

Replacing the fuel filter

Check the fuel screen in the carburettor

Have checked by qualified expert per-

sonnel

Tank lid ventilation defective

Check that the tank lid ventilation is open,

if necessary replace the tank lid

Poor fuel quality

Check the fuel quality, if necessary

change the fuel

Engine does not

run with full speed

Throttle cable defective

Have checked by qualified expert per-

sonnel

Troubleshooting – Engine malfunctions

BVT 65

Go to

Discount-Equipment.com

order your parts

Содержание Bomag BVT 65


































































































Результаты поиска

Содержание Bomag BVT 65

Отзывы:

Fayat Group Bomag BVT 65, Инструкция по эксплуатации, Инструкция по обслуживанию, Страница: 87 / 97

Результаты поиска

Содержание Bomag BVT 65

Отзывы: