Fayat Group Bomag BVT 65 Скачать руководство пользователя

Страница: 15 / 97

3.1 General prerequisites

3.1.1 General

This BOMAG machine has been built in compliance with the latest

technical standard and complies with the applicable regulations

and technical rules.

However, dangers for persons and property may arise from this

machine, if:

it is used for purposes other than the ones it is intended for,

it is operated by untrained personnel,

it is changed or converted in an unprofessional way,

the safety instructions are not observed.

Each person involved in the operation, maintenance and repair of

the machine must therefore read and comply with these safety reg-

ulations. If necessary, the customer must obtain the relevant signa-

tures as confirmation.

Furthermore, the following obviously also applies:

applicable accident prevention instructions,

generally accepted safety and road traffic regulations,

country specific safety regulations.

It is the duty of the operator to be acquainted with the safety regu-

lations and to apply these accordingly. This also applies for local

regulations amnd regulations concerning different types of handling

activities. Should the recommendations in these instructions be dif-

ferent from the regulations valid in your country, you must comply

with the safety regulations valid in your country.

3.1.2 Explanation of warning signs:

DANGER!
Danger to life if failing to comply!

Sections marked accordingly indicate an extremely

dangerous situation that could lead to fatal or severe

injuries, if this warning is disregarded.

WARNING!
Danger to life or danger of severe injuries if failing

to comply!

Sections marked accordingly indicate a dangerous sit-

uation that could lead to fatal or severe injuries, if this

warning is disregarded.

Concerning your safety – General prerequisites

BVT 65

Go to

Discount-Equipment.com

order your parts

Содержание Bomag BVT 65


































































































Результаты поиска

Содержание Bomag BVT 65

Отзывы:

Похожие инструкции для Bomag BVT 65

Бренды по названию

Популярные бренды

Fayat Group Bomag BVT 65, Инструкция по эксплуатации, Инструкция по обслуживанию

Результаты поиска

Содержание Bomag BVT 65

Отзывы:

Похожие инструкции для Bomag BVT 65

Бренды по названию

Популярные бренды