manualshive.com logo in svg

Fasep B350.G3, Руководство пользователя

Поделиться
Скачать
Fasep B350.G3 Скачать руководство пользователя страница 13

Fasep 2000 srl

Rev. 1.1

Balatron B350.G3

10 September 2012

5-1

5

MEASUREMENT AND CORRECTION OF UMBALANCE

5.1

Placing the wheel on the wheel balancer

5.1.1

Select the cone or flange suitable for the wheel to be balanced.

NOTE

:

the operation of centering and tightening of the wheel on the flanges is of basic importance for correct

balancing. Good results depend on proper performance of these procedures.
Clean accurately all cones, shaft and adappter surface before placing the wheel on the wheel balancer.

!

CAUTION:

Always make sure flanges are correctly locked on the motor shaft and wheel is correctly locked on
the flange being used

.

5.2

How to compensate umbalance of flanges using AFC function

NOTE

:

This operation allows to put compensate unbalance of flange and other accessories.

5.2.1

Lock the required flange on the shaft without the wheel.

HOW TO TURN ON AFC FUNCTION

The ZERO led blinks.

The ZERO led is on.

HOW TO TURN OFF AFC FUNCTION

Remove the flange.

The ZERO led switch off.

Содержание B350.G3























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды