manualshive.com logo in svg

Farymann Diesel 15B Series, Руководство оператора

Поделиться
Скачать
Farymann Diesel 15B Series Скачать руководство пользователя страница 83

 

Diesel engine Series 15B / 18B 

 

Maintenance 

 

 

2008-09-08

  

83 

 

Adjusting exhaust valve 

 

Fig. 14 

5. 

Insert crank handle (1) into the starting handle support 
bearing and slowly turn the crankshaft clockwise until the inlet 
valve's spring is pushed down completely (inlet valve is now 
fully open). 

 

Fig. 15 

6. 

Slide a feeler gauge (5) with thickness 0.1 mm between 
rocker arm (4) and the exhaust valve stem and check the 
valve clearance of the exhaust valve.  
The feeler gauge must be able to be pulled through without 
noticeable resistance (drag). 

 

Fig. 16 

7. 

If the clearance is too large or too small, undo the lock nut (6) 
and adjust the clearance with the adjusting screw (7). The 
feeler gauge must be able to be pulled through without 
noticeable resistance (drag). 

8. 

Hold the adjusting screw in place with a screwdriver and 
tighten the lock nut. 

9. 

Check the valve clearance again. 

 

  

 

Содержание 15B Series















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды