FarmTek Growers Supply GrowSpan Gothic Pro 106306D Скачать руководство пользователя страница 26

Страница: 26 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

INSTALL MAIN COVER

Gather the parts:
•  Main covers and inflation fan kit
•  U-Channel spring (#102198)
•  Ropes long enough to reach over the frame (provided

by customer)

• Box cutter or utility knife

Assembly Procedure

After the poly latch U-channel is attached to the frame,

unpack the main cover and pull into place. Ropes or straps

are typically used to pull the main cover onto and over the

frame

WARNING:

To prevent damage to the cover and to

prevent serious personal injury, DO NOT attempt to

install the main cover on windy or stormy days.

INSTALL POLY LATCH U-CHANNEL (continued)

The steps that follow describe one way to complete this

process.

ATTENTION: Install the IR film cover first! Examine the

IR film and install with the correct side facing in the

direction indicated on the film.

1. Take the cover film and position it along the base of

one side of the greenhouse.

NOTE:

Unfold the cover and locate the leading edge

The frame shown in the photos that follow differs from

actual frame. Procedure is the same.

Photo shows the cover film in position to pull over the

greenhouse.

2. Along the edge, make small holes in the cover at

evenly spaced intervals and tie rope or straps to the

cover.

NOTE:

The ropes or straps must be long enough to

reach over the top of the building to the other side.

Long buildings require additional ropes to prevent

tearing the main cover when it is pulled into place.

Keep the holes, used to attach the rope or straps, near

the edge of the material and below where the cover will

be secured to the U-channel.

Consult the Spec Sheets for cover identification. The

greenhouse is equipped with double-layer main cover and

an inflation fan kit. One cover is pulled into position and

anchored to the frame, then the inflation kit is installed, and

finally the last main cover is attached.

NOTE:

Insert shows installation of u-channel on top

of an end rafter. U-channel will bend with the curve of

rafter as it is attached.

Install screws at 12" on-center.

6. Continue to attach u-channel until it is installed on top

both end rafters

Top edge of

end rafter

Location of the side runs of U-channel and ribbon board.

3. Continue to attach u-channel to ribbon board and

work toward the other end of frame. Cut last section of

u-channel to required length so it is flush with end wall

panel.

4. Repeat these steps for remaining side.
5. After attaching u-channel to frame sides, use Tek

screws to attach the 102197 u-channel to top edge of

the end rafters.

Space at 16" on-center.

Содержание Growers Supply GrowSpan Gothic Pro 106306D






















































Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Gothic Pro 106306D, Руководство по сборке

Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды