FarmTek Growers Supply GrowSpan Gothic Pro 106306D Скачать руководство пользователя страница 16

Страница: 16 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

4. Secure the base tube between the legs of the end

rafter using an angle bracket and Tek screws.

INSTALL THE END WALL FRAME (continued)

The bracket

shown in this

diagram can

be installed

with either its

short section

(as shown) or

the long section

attached to the

ground post.

Base Tube

Ground

Post

5. On the base tube surface facing the inside of the

greenhouse, install a short Tek screw at each joint and

then locate and mark the center of the base tube.

6. Consult the End frame diagram (Quick Start section)

and mark the rough opening for the width of the double

door assembly.

7. Place the band clamps on the end rafter above the

door as shown below.

DO NOT TIGHTEN THE BOLTS

AT THIS TIME.

ATTENTION:

The frame shown below may differ from

the end wall frame. Consult the diagrams in the Quick

Start section to view the frame for this shelter.

8. Select the tubing for the two vertical frame supports for

the sides of the double door. Each support includes:

9. Measure the distance

between the top of the base tube

and band clamp (Step 7)

to determine the length of the

first vertical section of the door frame tube.

10. Choose one (1) square tube (#102897), insert the

swaged end of the long tube into the plain end of

another tube and tap with a hammer to properly seat

the tubes at the joint.

11. On this assembled frame member, mark the length

determined in Step 9 (above) and

subtract the amount

needed to account for the square-to-round tube

connect bracket

, which is attached to the top of the

frame tube. See the diagram that follows.

12. Select a square-to-round tube connect bracket and

attach the bracket to one end of the vertical frame

member. Use a 5/16" drill bit to drill a hole through the

tube and attach the bracket to the tube using a nut and

carriage bolt.

13. Repeat Steps 9-12 for the remaining vertical frame

member for the door.

14. With the square-to-round tube connect bracket

attached to the top of each vertical door frame tube,

use the bolt in the band clamp to attach the bracket to

the band clamp. DO NOT TIGHTEN AT THIS TIME.

NOTE:

The heads of the bolts for each clamp are to the

outside (or front/back) of the greenhouse. At this point,

the two vertical door frame members should be loosely

attached to the end rafter assembly.

• One (1) long 99" section of square tubing (#102897

swaged end)

• One (1) short section of square tubing. This is cut

from a swaged end tube (#102897).

• One (1) square-to-round tube bracket (#104074)

End Rafter

Square-to-

Round Tube

Connect

Bracket

Front (or outside)

of the greenhouse

Vertical Door

Frame Tube

Содержание Growers Supply GrowSpan Gothic Pro 106306D






















































Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Gothic Pro 106306D, Руководство по сборке

Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды