FarmTek Growers Supply GrowSpan Gothic Pro 106306D Скачать руководство пользователя

Страница: 22 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

END PANEL INSTALLATION (continued)

The greenhouse in this photo is used for illustration

only. It is of a different model.

4. Continue installing the polycarbonate panels and

aluminum profile in the locations shown on the end

panel diagrams (Quick Start section) for the front and

back end walls.

ATTENTION:

The U-channel profile for the top edge of

all panels (dashed line below) is installed last and after

all profile is installed along the edges and between

each panel as shown on the end panel diagrams.

Cut upper panel

to proper length.

Frame shown above may differ from actual frame.

NOTE:

The outside edges of the panels are finished

with the aluminum U-channel profile. Consult the

arrows above and the end panel diagrams at the back

of these instructions.

Aluminum U-channel profile is also installed at the

bottoms of the panels above the doors to finish those

edges.

5. After installing all panels, cut and attach the aluminum

profile to the remaining upper edge of all polycarbonate

panels.

NOTE:

For the rounded edges of the panels, prepare

the U-channel profile as shown in the photos that

follow:
a. Cut angled notches from the aluminum profile to

allow bending of the profile. The tighter the curve,

the closer the notches.

b. The distance between the notches is determined

by the degree of the bend required to fit the rafter.

c. Bend the U-channel profile at the notches before

installing it.

6. Repeat the procedure for the remaining end panels for

the other end of the greenhouse.

7. Continue with the

Double Door Assembly

procedures

that follow.

Install profile here.

Upper Panel

In this photo, the top of the panel is removed using a

power tool equipped with a round cutting bit. A utility

knife can also be used.

Содержание Growers Supply GrowSpan Gothic Pro 106306D






















































Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Gothic Pro 106306D, Руководство по сборке

Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды