FarmTek Growers Supply GrowSpan Gothic Pro 106306D Скачать руководство пользователя страница 29

Страница: 29 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

The drop-down curtain requires a ribbon board to secure its

upper section and a baseboard to secure its lower section.

The materials for these components are not included and

are

supplied by the customer

BASEBOARDS AND RIBBON BOARDS

The example above shows the required ribbon board and

baseboard as attached to the frame.

ATTENTION:

Consult the Main Cover Details diagram in

the Quick Start section of this manual to determine where

to install the ribbon board.

The ribbon board consists of two runs of material; the first

is a 2" x 6" board attached to the building frame and the

second is a 1" x 4" board attached to the first board. These

boards, when assembled properly, provide a channel that

secures the curtain when it is in the up or closed position.

Boards are secured to the frame using the supplied

1/4" x 4" carriage bolts and to each other using the FA4652

supplied fasteners.

The diagram below shows a customer-supplied ribbon

board as attached to the frame.

Ribbon Board

Baseboard

FRAME CHECK AND CURTAIN PREPARATION

1. Attach the second board to the ribbon board using

FA4652 wood screws as shown in the diagram to the

left.

2. Verify that the baseboard is installed properly at ground

level. The baseboard must be level for the drop-down

curtain to install and function properly.

3. Gather the boards needed for the retaining board of the

baseboard. See diagram above.

4. Collect all drop-down curtain components and continue

with the curtain installation.

A customer-supplied baseboard and retaining board are

also required to attach the curtain's lower edge. See the

exploded view that follows.

The baseboard runs the length of the frame at ground level.

The retaining board secures the curtain to the baseboard.

The baseboard and retaining board are supplied by the

customer.

Fasteners (1/4" x 4" carriage bolts and FA4652 wood

screws) are included. Depending on board width, use 2

carriage bolts per rafter connection for the baseboard and

ribbon board. Evenly space the wood screws at 24".

Rafter

2" x 6" Board

1" x 4" Board

FA4652

Wood

Screws

1/4" x 4"

Carriage

Bolts

U-Channel

End Panel of Shelter

Curtain

Panel

Ground Level

Baseboard and

Retaining Board

Secure

u-channel to

ribbon board

using FA4652

wood screws

spaced at 16"

on-center.

Содержание Growers Supply GrowSpan Gothic Pro 106306D






















































Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Gothic Pro 106306D, Руководство по сборке

Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды