FarmTek Growers Supply GrowSpan Gothic Pro 106306D Скачать руководство пользователя страница 10

Страница: 10 / 53

GROWSPAN

™

GOTHIC PRO GREENHOUSES AND SYSTEMS

Revision date: 06.07.18

INTERIOR RAFTER ASSEMBLY
Complete the following steps

for the interior rafters

1. Select the pipes for the first interior rafter assembly and

position these on the ground as shown.

(#26G166SS401D)

(#166S099)

(#26G166SS403)

IMPORTANT:

Interior rafters do not use end clamps.

Instead, cross connectors are attached during the

frame assembly.

2. Insert the swaged ends of the rafter pipes into the plain

ends of the pipes and secure each joint with a Tek

screw.

NOTE:

For longer frames, it may be easier to assemble

a few rafters at a time and then begin to assemble the

frame. Position Tek screws so they will not contact the

cover when the frame is assembled.

3. Once rafters are assembled, assemble the frame.

FRAME ASSEMBLY

After all ground posts are driven in place and rafters are

assembled, assemble the frame.

NOTE:

The required baseboards shown in the diagrams

throughout these instructions are not included and must be

supplied by the customer.

Contact Customer service at 1-800-245-9881 to purchase

baseboards, or for additional information.

ASSEMBLE AND PRE-MARK THE PURLINS

The following steps describe one way to speed the

assembly process and eliminate the need to measure each

purlin as it is installed. Pre-marking the purlins ensures that

an accurate spacing of the rafter assemblies is achieved

and maintained during assembly.

Gather the Parts:
•  Pipe 1.315'' x 75'' swaged (#131S075)
•  Pipe 1.315'' x XX'' plain (#131P0XX)
•  Marker and tape measure

NOTE:

The purlins are part of the assembled frame and

run perpendicular to the rafter assemblies. Each purlin

consists of 1.315" x 75" (#131S075) swaged pipes (number

is determined by shelter length) and one (1) 1.315" x XX"

(#131P0XX) plain pipe.

ATTENTION:

The XX" represents the remaining length

required to reach the end of the shelter. Consult the Spec

Sheet for part identification.
1. Select the required pipe sections for one purlin and

connect these by inserting the swaged ends of the

pipes into the plain ends until the entire purlin is

assembled.

NOTE:

Assemble the purlins in a location that is

accessible during the assembly of the frame, but will

not interfere with the process of lifting and setting the

rafters.

2. Verify that each pipe joint is properly seated.

NOTE:

These pipes must be separated during the

assembly procedure. Do not fasten them together at

this time.

3. For the 48" rafter spacing, measure forty-eight and

three-quarters inches (48-3/4") from one end of the

assembled purlin and mark the distance on the pipe.

NOTE:

This first measurement is three-quarters (3/4)

of an inch longer than the on-center rafter spacing

to account for the length of purlin pipe that extends

through the end purlin clamp of the first end rafter.

RAFTER ASSEMBLY (continued)

Содержание Growers Supply GrowSpan Gothic Pro 106306D






















































Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды

FarmTek Growers Supply GrowSpan Gothic Pro 106306D, Руководство по сборке

Результаты поиска

Содержание Growers Supply GrowSpan Gothic Pro 106306D

Отзывы:

Похожие инструкции для Growers Supply GrowSpan Gothic Pro 106306D

Бренды по названию

Популярные бренды