FarmTek FodderPro 2.0 Micro System Скачать руководство пользователя страница 6

Страница: 6 / 43

111628M

Revision date: 09.25.18

Important Information

SPECIAL NOTES AND CAUTIONS

The support frame for the 111628M FodderPro 2.0 Micro System is

designed to save assembly time and to better serve your growing needs.

Before you begin, read the information that follows.

CAUTION!

DO NOT CLIMB ON FRAME!

TO PREVENT INJURY AND POSSIBLE DAMAGE TO THE

FODDER SYSTEM AND RELATED COMPONENTS, NEVER

CLIMB ON THE ASSEMBLED OR PARTIALLY ASSEMBLED

FRAME.

NEVER USE THE FRAME ENDS AS A LADDER TO REACH THE

UPPER LEVEL OF THE FODDER FRAME!

ALWAYS POSITION THE FODDER CHANNELS ON THE

DIFFERENT LEVELS IN A WAY THAT EVENLY DISTRIBUTES THE

WEIGHT. NEVER LOAD ALL HEAVY CHANNELS ON ONE SIDE

OR ON THE TOP LEVEL OF THE ASSEMBLED FRAME. ALWAYS

PLACE HEAVY CHANNELS ON THE LOWER LEVELS ON EACH

SIDE OF THE FRAME.

NEVER REMOVE MATURE FODDER FROM CHANNELS ON

ONE SIDE OF THE FRAME ONLY. ALTERNATE FROM SIDE

TO SIDE TO MAINTAIN EVEN WEIGHT ON THE FRAME WHEN

HARVESTING FODDER.

AFTER FRAME SLOPE IS SET, ANCHOR THE BASE RAIL

OF EACH FRAME END TO THE CONCRETE USING ANCHOR

BOLTS WHEN POSSIBLE. PURCHASE BOLTS LOCALLY OR

CALL YOUR SALES REPRESENTATIVE FOR ADDITIONAL

INFORMATION.

CONSULT THE SERVICES OF A QUALIFIED CONTRACTOR FOR

OTHER WAYS TO ANCHOR YOUR SYSTEM WHEN IT IS NOT

POSITIONED ON CONCRETE.

ATTENTION:

CONSULT ALL DIAGRAMS AND THOSE NEAR THE

BACK OF THIS GUIDE TO IDENTIFY CRITICAL DIMENSIONS, PART

NUMBERS, AND PART LOCATIONS FOR THE FODDER FRAME.

Diagram above shows the end frame for your

111628M

FodderPro 2.0 Micro System.

Содержание FodderPro 2.0 Micro System












































Результаты поиска

Содержание FodderPro 2.0 Micro System

Отзывы:

Похожие инструкции для FodderPro 2.0 Micro System

Бренды по названию

Популярные бренды

FarmTek FodderPro 2.0 Micro System, Руководство пользователя

Результаты поиска

Содержание FodderPro 2.0 Micro System

Отзывы:

Похожие инструкции для FodderPro 2.0 Micro System

Бренды по названию

Популярные бренды