FarmTek FodderPro 2.0 Micro System Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 43

FarmTek FodderPro 2.0 Micro System Скачать руководство пользователя страница 9

9

Revision date: 09.25.18

111628M

1

ASSEMBLE MAIN FRAME: Attach Support Arms (End Frames)

Gather the parts and complete the steps that follow to attach the

support arms to the assembled end support frames.

Assembly Instructions

Required parts:
• (2) Assembled end support frames (from previous page).

These include

the longer 111628A base rail.

• (16) S15P027 Square Tube (plain) for support arms
• FA4482B Tek Screws and 100441 Magnetic Nut Setter

ATTENTION:

Install Tek screws as shown for best results and a uniform

appearance.

Review all diagrams for clarification.

Complete these steps:
1. Position one end support frame on a flat surface.
2. Slide one S15P027 square tube into the lower 4-way connector and

secure it in place using an FA4482B Tek screw.

3. Repeat this process to attach all remaining support arms to complete the

first end support frame. See completed end support frame to the right.

4. With assistance, carefully move the frame to the location where the

fodder system will be assembled.

5. Repeat the above steps to assemble the remaining end support frame.
6. Continue with the assembly of the two (2) long base rails as shown on

the next page.

S15P027

S15P027

111628A Base Rail

FA4482B

Tek Screws

ASSEMBLE END SUPPORT FRAME

«
...
7
8
9
10
11
...
»

Содержание FodderPro 2.0 Micro System












































Отзывы:

Нет отзывов