FarmTek FodderPro 2.0 Micro System Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 43

FarmTek FodderPro 2.0 Micro System Скачать руководство пользователя страница 17

17

Revision date: 09.25.18

111628M

3

ASSEMBLE THE DRAIN MANIFOLD

Required parts:
• 111560 2" PVC Pipe, WF6717 Slip Caps, and 111696

Double Hub (Cross Fitting)

•  111906 1" Sammys and 111907 Conduit Hangers
•  FAK26 Threaded Rods and FALB04B Nuts
•  113372 Primer and WF6990 PVC Cement

Assembly Instructions

Complete these steps:
1.  Cut 8 horizontal tubes at 24" each. Use the 2" (111560) PVC.
2.  Clean the ends of the PVC tubes to remove any loose material.
3.  Mark the hole locations on each 24" tube and drill the holes for the drain

elbows of the channels. Use a

1 3/8" hole saw bit

and a drill. (If possible,

drill the holes in the PVC tube using a drill press for accuracy.) Remove

loose material from around the holes and from inside each tube.

4. After cleaning each 24" tube, attach the WF6717 slip cap to the end of the

tube as shown.

DO NOT CEMENT THE CAPS TO THE TUBES. Caps

must remain free for cleaning of the tubes. Set these tubes aside for

later assembly of the drain manifold.

5. Using the 111560 2" PVC pipe, cut three (3) pieces at 8".
6. Take the 111696 cross fittings and 8" tubes and assemble the center stack

of the drain manifold as shown.

Use PVC primer and cement to attach

the vertical 8" tubes to the cross fittings.

Assemble on a flat surface for

best results and to keep the fittings aligned.

STEP 3

24"

8"

10 1/2"

Center Line

8"

WF6717 Slip Cap–

Do not cement.

111696

Cross Fitting

111696

Cross Fitting

111696

Cross Fitting

111696

Cross Fitting

TOP

BOTTOM

DRAIN MANIFOLD –

CENTER STACK

Length

of each

tube: 8"

NOTE:

Cement all 8" PVC sections to

the 111696 Cross Fittings using primer

and pvc cement.

For best results, use a step bit if

available to drill the holes in the pvc

tubing.

«
...
15
16
17
18
19
...
»

Содержание FodderPro 2.0 Micro System












































Отзывы:

Нет отзывов