manualshive.com logo in svg

Farm Fans C-21100B, Руководство пользователя, Страница: 59 / 66

Поделиться
Скачать
Farm Fans C-21100B Скачать руководство пользователя страница 59

57

A voltmeter is required for some of the following checkout
procedures.  Before performing any tests, make certain to
determine if dryer power supply is 3 PH 230V or 3 PH 460V.

The general control circuit and safety circuits are 115 volt on
all model dryers.  When checking these circuits, MEASURE
VOLTAGE BETWEEN THE CIRCUIT TEST LOCATION
AND GROUND.

REFER TO WIRING DIAGRAMS AND PARTS LIST FOR
IDENTIFICATION OF PARTS AND ELECTRICAL TERMI-

NALS. When right- or left-hand side of dryer is mentioned,
it is as viewed from the rear end of the dryer (opposite fan
end).

CAUTION:  When making high voltage tests with
live circuits, be extremely careful to follow estab-
lished safety practices.  Turn power ON for test-
ing only.  DO NOT ATTEMPT TO MAKE THE

DRYER OPERATE BY USING A JUMPER WIRE TO
BYPASS A DEFECTIVE COMPONENT.

TROUBLE

CHECKOUT PROCEDURE & INFORMATION

Control Circuit
Not Energized - Shutdown
Indicator Lights OFF.

1.   POWER SUPPLY - Check that MAIN POWER SUPPLY and CIRCUIT BREAKERS are turned ON.
Also check for a tripped circuit breaker.
2.   FUSES - Check for blown safety circuit fuse(s).  See appropriate POWER CIRCUIT diagram for
location and number used.
3.   OVERLOAD RELAY - Check for tripped overload relay.
4.   STOP OR START SWITCHES - Check for a defective STOP or START switch.  Also check switch
wiring connections.
5.   1CR RELAY - Check for a defective 1CR relay, relay base, or faulty wiring.

Control Circuit Not
Energized - Shutdown
Indicator Light ON.

SHUTDOWN INDICATOR LIGHTS 

BURNER LOCKOUT (manual reset: press button on Flame Safeguard)

LOW GRAIN (auto resets immediately)

METER ROLL MONITOR (auto resets immediately)
PLENUM HI-LIMIT (auto resets after cooling)
GRAIN HI-LIMIT (auto resets after cooling)

ASC PANEL INDICATOR LIGHTS

Meter Roll Monitor Light (auto resets immediately)
Meter rolls rotation has not been sensed for (3) min.
A. Meter roll selector switch is off
B. Meter rolls jammed
C. Meter roll drive failed
D. Meter roll proximity switch requires adjustment

NOTE:  It is normal for the meter roll light to be ON when the control circuit is in the off position and
the main disconnect is powered.

Low Grain Light (auto resets immediately).  Indicates Load Timer has been energized longer

than set time for the following possible reasons:

A.

Insufficient grain supply to fill dryer

B.

Load timer set incorrectly:

load time set too low
timer set to incorrect range
timer memory set incorrectly to ON

C. Failed load drive

Plenum High Light (auto resets after cooling).  Indicates Plenum Hi-limit switch has reached

300°F for the following possible reasons:

A.

Plenum temperature set too high

B.

Minimum gas pressure setting too high

C.

Plenum controller failed

D.

Plenum RTD failed

E.

Plenum hi-limit switch failed

Содержание C-21100B



































































Отзывы:

Нет отзывов