Fargo DTC4500e Скачать руководство пользователя страница 62

Страница: 62 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 62

Remove/Replace Encoder Sensor (A930514)

for RFID Supply Spindle

NOTE:

For

any other parts (motor/ encoder wheel) REPLACE COMPLETE ASSEMBLY (D930015).

Step Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Remove Supply Spindle-RFID assembly. Refer to:

Remove/Replace Supply Spindle RFID Motor

(D930015) DTC4500e

Remove/Replace Supply Spindle RFID Motor (D930015)

DTC1250e/4250e

A000365-01

Tools needed:

Torx screwdriver and flat head screwdriver

Estimated Repair Time: 30 min

Preparation:

Remove the Covers

Important:

This procedure can only be performed by

authorized service personnel.

RFID Cable D930603

Encoder Sensor Cable D930605

Содержание DTC4500e


















































































































































Результаты поиска

Содержание DTC4500e

Отзывы:

Похожие инструкции для DTC4500e

Бренды по названию

Популярные бренды

Fargo DTC4500e, Руководство по обслуживанию

Результаты поиска

Содержание DTC4500e

Отзывы:

Похожие инструкции для DTC4500e

Бренды по названию

Популярные бренды