Fargo DTC4500e Скачать руководство пользователя страница 112

Страница: 112 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 112

DTC Printhead procedure

The guide serves to instruct the user about replacing the Printhead. This procedure can only be
performed by authorized service personnel.

Caution:

Turn OFF the Printer and unplug the power cord from the Printer.

Danger:

Wear proper eye protection to perform the procedures in this section.

Reverse the disassembly steps to reassemble the Card Printer. ESD precautions are
necessary when handling electronics assemblies.

Step Procedure
1

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Turn the printer over to access the Headlift cover.

Tools needed:

Flathead screwdriver

Torx Wrench (included in kit)

Estimated Repair Time: 20 minutes

Preparation:

Remove Printhead mount

Important:

This procedure can only be performed by

authorized service personnel.

Make

NOTE:

of the resistance value on the new

printhead; verify this value in the Advanced Settings
driver option. Refer to the User Guide for more
information.

Содержание DTC4500e


















































































































































Результаты поиска

Содержание DTC4500e

Отзывы:

Похожие инструкции для DTC4500e

Бренды по названию

Популярные бренды

Fargo DTC4500e, Руководство по обслуживанию

Результаты поиска

Содержание DTC4500e

Отзывы:

Похожие инструкции для DTC4500e

Бренды по названию

Популярные бренды