Fargo DTC4500e Скачать руководство пользователя страница 88

Страница: 88 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 88

Parts Replacement- Lamination Module

Remove/Replace the Lamination Module Mainboard

Step Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Remove the Lamination Module from the printer base to access the mainboard.

Turn the module up-side down to access the 4 screws (F000178) that hold the mainboard to the
frame. Remove the 4 screws.

Use caution when removing the mainboard so the power connector does not get damaged. Slide the
board away and out from the frame.

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 20 min

Preparation:

Remove the Lamination Module Covers

Important:

This procedure can only be performed by

authorized service personnel.

DTC4500e (single side) A920221-11

DTC4500e (dual side) A920221-12

Содержание DTC4500e


















































































































































Результаты поиска

Содержание DTC4500e

Отзывы:

Похожие инструкции для DTC4500e

Бренды по названию

Популярные бренды

Fargo DTC4500e, Руководство по обслуживанию

Результаты поиска

Содержание DTC4500e

Отзывы:

Похожие инструкции для DTC4500e

Бренды по названию

Популярные бренды