Fargo DTC4500e Скачать руководство пользователя страница 76

Страница: 76 / 90

DTC4500e_User Guide_EN, PLT-01669, Rev. 1.1

Page 76

April 2014

Error Message

Cause

Solution

# 44
Flipper Jam/ Home

Error

A card has become jammed in

the printer’s flipper table.
The flipper failed to position

properly while aligning a card or

flipping a card.

Clear any cards in the flipper table

using the buttons to move the

card out. Resume printing.
The flipper table should be level

when the printer is powered up. If

the flipper Table is at an angle,

open the card output door and

manually level it. Then cycle the

printer power to reset.
Reset the printer and retry. If

problem persists call for technical

assistance.

# 45
No Flip Module

installed

Request to print on 2

side of

card, but no flipper is installed.

If a Flipper Module is present,

ensure that the Print Both Sides

option in the printer driver is set

correctly.
Install a flipper module.

# 60
Laminator Calibration

Fail

LED calibration error occurred.

Try again.

# 64
# 65
# 66
Reboot Required

Unspecified system error

detected by the printer firmware.

Reset the printer and try again.
If this problem persists, call for

technical assistance.

# 67
General

Utility command does not exist.

Verify the command and reenter.

# 68
Card in Printer

A card is jammed in the print

station or card flipping area of

the Printer.

Clear the jam and press the

Pause

button.

Содержание DTC4500e



























































































Результаты поиска

Содержание DTC4500e

Отзывы:

Похожие инструкции для DTC4500e

Бренды по названию

Популярные бренды

Fargo DTC4500e, Руководство пользователя

Результаты поиска

Содержание DTC4500e

Отзывы:

Похожие инструкции для DTC4500e

Бренды по названию

Популярные бренды