Fanvil FV6030 Скачать руководство пользователя страница 48

Страница: 48 / 62

- 48 -

Syslog server receives the messages from clients, and classifies them based on priority and type.

Then these messages will be written into log by some rules which administrator can configure.

This is a better way for log management.

8 levels in debug information:

Level 0---emergency: This is highest default debug info level. You system can not work.

Level 1---alert: Your system has deadly problem.

Level 2---critical: Your system has serious problem.

Level 3---error: The error will affect your system working.

Level 4---warning: There are some potential dangers. But your system can work.

Level 5---notice: Your system works well in special condition, but you need to check its working

environment and parameter.

Level 6---info: the daily debugging info.

Level 7---debug: the lowest debug info. Professional debugging info from R&D person.

At present, the lowest level of debug information send to Syslog is info, debug level only can be

displayed on telnet.

Syslog Configuration

Field name

explanation

Server IP

Set Syslog server IP address.

Server Port

Set Syslog server port.

MGR Log Level

Set the level of MGR log.

SIP Log Level

Set the level of SIP log.

IAX2 Log Level

Set the level of IAX2 log.

Enable Syslog

Select it or not to enable or disable syslog.

4.3.5.3. Config Setting

Содержание FV6030































































Результаты поиска

Содержание FV6030

Отзывы:

Бренды по названию

Популярные бренды

Fanvil FV6030, Руководство пользователя

Результаты поиска

Содержание FV6030

Отзывы:

Бренды по названию

Популярные бренды