Fanvil FV6030 Скачать руководство пользователя

Страница: 41 / 62

- 41 -

DSP Configuration

Field name

explanation

First Codec

The fist preferential DSP codec: G.711A/u, G.722, G.723, G.729

Second Codec

The second preferential DSP codec: G.711A/u, G.722, G.723, G.729

Third Codec

The third preferential DSP codec: G.711A/u, G.722, G.723, G.729

Forth Codec

The forth preferential DSP codec: G.711A/u, G.722, G.723, G.729

Fifth Codec

The fifth preferential DSP codec: G.711A/u, G.722, G.723, G.729

Input Volume

Specify Input (MIC) Volume grade.

；

Handfree Volume

Specify Handfree Volume grade

G729 Payload Length

Set G729 Payload Length

Handdown Time

Specify the least reflection time of Handdown, the default is

200ms.

Ring Type

Select Ring Type

Output Volume

Specify Output (receiver) Volume grade.

Ring Volume

Specify Ring Volume grade

G722 Timestamps

160/20ms or 320/20ms is available

G723 Bit Rate

5.3kb/s or 6.3kb/s is available

Default Ring Type

Set up the ring by default

Signal Standard

Select Signal Standard.

VAD

Select it or not to enable or disable VAD. If enable VAD, G729

Payload length could not be set over 20ms.

4.3.4.2. Call Service

In this web page, you can configure Hotline, Call Transfer, Call Waiting, 3 Ways Call, Black List,

white list Limit List and so on.

Содержание FV6030































































Результаты поиска

Содержание FV6030

Отзывы:

Похожие инструкции для FV6030

Бренды по названию

Популярные бренды

Fanvil FV6030, Руководство пользователя

Результаты поиска

Содержание FV6030

Отзывы:

Похожие инструкции для FV6030

Бренды по названию

Популярные бренды