background image

IMPORTANT INFORMATION

 

 

Warranty Policy Shortlist

 

 

Warranty does not cover :-

 

•  Correcting faults caused by incorrect installation of a product.

 

•  Where an engineer cannot gain access to a site or a product.

 

•  Repeat commission visits.

 

•  Replacement of any parts where damage has been caused by misuse.

 

•  Engineer waiting time will be chargeable.

 

•  Routine maintenance and cleaning.

 

•  Gas conversions i.e. Natural to Propane gas.

 

•  Descaling of water products and cleaning of water sensors where softeners/ conditioners are not fitted, 

or are fitted and not maintained.

 

•  Blocked drains

 

•  Independent steam generation systems.

 

•  Gas, water and electrical supply external to unit.

 

•  Light bulbs

 

•  Re-installing vacuum in kettle jackets.

 

•  Replacement of grill burner ceramics when damage has been clearly caused by misuse.

 

•  Where an engineer finds no fault with a product that has been reported faulty.

 

•  Re-setting or adjustment of thermostats when unit is operating to specification.

 

•  Cleaning and unblocking of fryer filter systems due to customer misuse.

 

•  Lubrication and adjustment of door catches.

 

•  Cleaning and Maintenance

 

• Cleaning of burner jets

 

• Poor combustion caused by lack of cleaning

 

• Lubrication of moving parts

 

• Lubrication of gas cocks

 

• Cleaning/adjustment of pilots

 

• Correction of gas pressure to appliance.

 

• Renewing of electric cable ends.

 

• Replacement of fuses

 

• Corrosion caused by use of chemical cleaners.

 

Содержание Dominator Plus G3151











Отзывы: