Factory Five Racing Type 65 Coupe Скачать руководство пользователя страница 399 | Manualshive

Страница: 399 / 442

background image

398

www.factoryfive.com

508-291-3443

Shocks/Springs

Using the Mustang rear coil springs and shocks gives a comfortable ride. For a slightly stiffer
suspension, replace the stock rear shocks with aftermarket units. We have found that KYB makes an
inexpensive good replacement that roughly 20% stiffer than stock.

For the well balanced fun to drive car, the 3-link rear suspension combined with the Factory Five custom
valved Koni rear coil-over shocks work the best.

Factory Five offers a couple different shock/spring packages.
An affordable rear coil-over package which includes shocks and 350 lb/in springs.

A road racing oriented 3-Link and front coil-over package, which includes stiffer valved shocks and 750
lb/in front springs and 500 lb/in rear springs.

High Performance Manual Braking Systems

The braking systems recommended below are designed for those searching for higher performance
braking capabilities. These are systems that have been used successfully by our customers and us. Each
component below has been selected to optimize the capabilities of the system. If an attempt is made to
utilize some of the specified components, but not all of them in combination, then braking abilities may
not be satisfactory.



For

all

manual braking setups use the brake pedal from a 1984 4-cylinder Mustang (Ford Part

#08BZ2455A), this pedal can also be made by modifying the V8 Mustang pedal as specified in
the FFR Manual (this modification should be done by a professional shop).



Some of the setups may not clear some wheel sizes and designs.



For

all

rear disc brake setups, use a proportioning valve on the

front

brakes.



We recommend using Porterfield R-4, Carbotech XP8 or 9, or Hawk Blue brake pads. Though
costly, you will find a significant difference in your cars ability to stop. If these pads are out of
your price range, next in line would be Performance Friction Z-Compound pads available at
Autozone.

4-lug (4.25” pattern)

Master Cylinder

– FFR

15

/

16

” Master cylinder/Proportioning valve (FFR#14739

«
...
397
398
399
400
401
...
»

Содержание Type 65 Coupe



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Type 65 Coupe

ESCALADE - BROCHURE 2009

Бренд: Cadillac Страницы: 24

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 20

Electronic Parking Disc II

Бренд: Jacob Jensen Страницы: 28

Бренд: Jeep Страницы: 5

Бренд: Jeep Страницы: 6

Grand Cherokee SRT 2014

Бренд: Jeep Страницы: 345

Grand Cherokee 2015

Бренд: Jeep Страницы: 236

Бренд: Jeep Страницы: 18

Бренд: Jeep Страницы: 24

Бренд: Jeep Страницы: 560

Бренд: Jeep Страницы: 525

Бренд: Jeep Страницы: 308

Бренд: Jeep Страницы: 86

Бренд: Jeep Страницы: 638

Бренд: Jeep Страницы: 9

Бренд: Jeep Страницы: 51

Бренд: Jeep Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды