Factory Five Racing Type 65 Coupe Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 442

background image

32

www.factoryfive.com

508-291-3443

Front Wiring Harness



Socket set, extension, regular, Phillips head screwdrivers, needle nose pliers, hammer, and
marker tape.



Front wiring harnesses.

Pull the rubber grommet out of the firewall into the engine bay.
Remove the front light harness from the engine bay wall working from the starter solenoid area to the
alternator. Unscrew any ground wires and mark the connectors (Especially the headlight and turn signal
lights) as you go.

87-93 Front wiring harness with hookups for headlights, alternator, and horn.

Speedometer and Clutch Cables



Socket set, duct tape.



Speedometer cable and sending unit, clutch cable.

Pull the speedometer cable out from the dash area keeping the rubber grommet that is on it in place.
This grommet will also get used.
Remove the bolt that holds the cable to the body near the exhaust in the engine bay.
Remove the wiring harness plug from the sending unit.
Remove the speedometer sending unit bolt using an 11mm socket.
Pull the sending unit straight out.
Replace the screw in the transmission once the sending unit is removed.
Cover the speedometer drive hole with duct tape to prevent dust and dirt from entering.
Remove the clutch cable cover from the bell housing and push the cable out of the clutch fork.

«
...
31
32
33
34
35
...
»

Содержание Type 65 Coupe



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Type 65 Coupe

Бренд: Cargo Floor Страницы: 16

Бренд: Chevrolet Страницы: 376

Бренд: Mazda Страницы: 15

Бренд: hc-cargo Страницы: 60

Бренд: Würth Страницы: 36

Бренд: Mercedes-Benz Страницы: 39

Бренд: Vangear Страницы: 5

Бренд: Safe Fleet Страницы: 20

Бренд: Ratio Страницы: 12

Бренд: Horn Tools Страницы: 8

Бренд: Ford Страницы: 52

Бренд: Thule Страницы: 8

Бренд: Fiat Страницы: 284

CERTA CTCVINCVR14A

Бренд: Kogan Страницы: 4

Бренд: Maserati Страницы: 37

Бренд: Magneti Marelli Страницы: 3

Бренд: Painless Performance Страницы: 16

Бренд: EUFAB Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды