Factory Five Racing Type 65 Coupe Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 442

background image

36

www.factoryfive.com

508-291-3443

Use duct tape or zip ties to secure the lower radiator hose up to the power steering pump area so that it
will not spill fluid as the engine is removed later.



Get help with the next few steps, as the parts involved are heavy!

Attach an engine hoist to the engine lift points at the driver’s front and passenger’s rear areas of the
engine.  One easy way to do this is with a chain and bolt on the other side of the hole. An alternative to
this is to wrap chains through the back of the engine mounts and bolt the chain together for lifting.  This
will give you a balanced lift point.
Take up the slack on the chain slowly.  Check to make sure that no hoses or wires remain connected to
the engine.
Remove the bolts from the transmission cross-member and remove the cross-member.
Check again to make sure that all wires and straps are removed.
Lift the engine off the engine mounts and guide it out of the engine bay.  Guide the rear of the
transmission out of the transmission tunnel carefully.
Set the engine/transmission assembly on an old tire with no rim or on engine stands to avoid damaging
the oil pan.

There is an exhaust H-pipe tube holder plate sandwiched between the transmission mount and the
transmission that must be removed.  All you need is the transmission mount with the two bolts sticking
down.

Front Suspension



Spring compression tool, socket set, wrenches, breaker bar, tubing cutter, floor jack, tire iron,
jack stands, chain, needle nose pliers, rags, ball joint removal tool or plastic dead blow hammer.



Brake calipers, rotors, spindles, front lower control arms.



The front springs are compressed in their fitted positions even when the suspension pieces are
lowered in their mounts! These springs will cause serious injury or death if you are not
extremely careful.

Loosen the lug nuts on the front wheels.
Raise the front of the car up with a floor jack and support it with jack stands.
Remove the front wheels.
Disconnect the front sway bar and remove the mounts from the control arms.
Follow the flexible brake line from the front brakes to the mounting bracket on the body, unscrew or cut
the steel brake line 4” after the bracket.
Remove the bracket clips from the brake line body mounts keeping them to use later.
Pull the brake line through the bracket. Put a rag or duct tape over the end to prevent brake fluid from
dropping on the floor.
Put a jack underneath the ball joint on the lower control arm.

«
...
35
36
37
38
39
...
»

Содержание Type 65 Coupe



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Type 65 Coupe

Бренд: Daihatsu Страницы: 41

Бренд: Daihatsu Страницы: 268

Бренд: Eclipse Страницы: 6

Бренд: Vauxhall Страницы: 2

Бренд: Jeda Страницы: 8

Бренд: Jeep Страницы: 496

Бренд: Warrior Winches Страницы: 17

BLACK STEEL S2560

Бренд: Fab Fours Страницы: 9

Бренд: iArmor Страницы: 6

Бренд: DAVIS Страницы: 32

Бренд: AC Schnitzer Страницы: 20

Road Ready Seat Protector

Бренд: Wagan Страницы: 12

Бренд: Chevrolet Страницы: 50

Бренд: TBC Страницы: 12

Бренд: Prorack Страницы: 14

Бренд: Renault Страницы: 340

Бренд: PAC Страницы: 14

Бренд: Kolpin Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды