Factory Five Racing Type 65 Coupe Скачать руководство пользователя страница 368 | Manualshive

Страница: 368 / 442

background image

367

www.factoryfive.com

508-291-3443

Pick a color wire for the sending unit wire and connect it to the gauge using a ring connector.
Attach the other end of the same color wire to the Mustang Brown plug # 10 (

gas tank sending unit

).

Battery Charging

In order for the battery to charge, solder a 510 OHM resistor between the wires on the red light forming
an H with the 2 wires.  This resistor can be found on the Mustang white gauge pod.  Carefully clip the
resistor leads leaving them as long as possible.  You may want to protect this junction with tape, etc.
solder the wires (with resistor soldered together ahead of wire ends) on the red dash light to two of the
wires on the second 4 conductor 2’ section.  Attach the other ends of the two wires to the Brown plug
pin #2 (

Ign. Sw. to Ign. Coil (BATT)

and brown plug pin #14

(Ign. Sw. (ACC) to Alt. Reg.

) using red

connectors. When starting the car, the light will turn on and then go off. The light is part of the circuit
and MUST be present.

High Beam Indicator

Connect one lead from the blue light to the black wire and the other lead to the second 4 conductor 2’
section.
Attach the other end of the same wire to the gray plug pin #2 (

Dimmer to High Beams

) using red

connectors.
The blue light will light when the high beams are on.

Turn Signal Indicator

In order for the green light to flash when either the right or left turn signals are turned on, a 3-prong turn
signal indicator is used.  Find the original 2-prong turn signal (probably round and light blue or
aluminum) in the Mustang dash wiring harness in front of the passenger seat or near the center of dash.
If it is not here, turn the turn signals on and follow the sound.  Remove the original flasher from the
wiring plug and carefully cut the two wire 90 degree wire connector in half leaving the wires connected
to each piece.  Put the wires on the left and right prongs of the 3-prong flasher.  Run the four foot blue
extension wire from the middle prong on the flasher to one of the wires on the green light.  Attach the
other wire on the green light to the black wire using a red connector.
Install the gauges, lights and switches using the instructions included with the gauges.

«
...
366
367
368
369
370
...
»

Содержание Type 65 Coupe



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Type 65 Coupe

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

Бренд: A-Tach Mounts Страницы: 2

QuadraTop Adventure Top S

Бренд: Quadratec Страницы: 20

Бренд: RAM Страницы: 116

Бренд: Carefree Страницы: 12

Бренд: Velleman Страницы: 6

Бренд: V8 equipment Страницы: 17

Бренд: Alfa Romeo Страницы: 8

Бренд: Thule Страницы: 12

Бренд: POOL-LINE Страницы: 2

Бренд: FIRRAK Страницы: 12

Бренд: SIXTOL Страницы: 32

Бренд: Kargo Master Страницы: 18

BLADE-AL-HK4-EN

Бренд: iDataLink Страницы: 35

Бренд: MovaNext Страницы: 4

iCarPlay Direct Connect 2000

Бренд: Monster Страницы: 66

Quad Gear 18-029-010401-00-SC

Бренд: Classic Accessories Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды