Factory Five Racing Type 65 Coupe Скачать руководство пользователя страница 376 | Manualshive

Страница: 376 / 442

background image

375

www.factoryfive.com

508-291-3443

Sitting inside with the door closed, hold the check straps up to the door and the 2”x 2” tube and position
the strap so that it will hit the framework in the door.
Use a marker and one of the check straps to mark the two mounting holes on the middle of the inside
face of the 2”x 2” vertical tube that the hinge is mounted on.
Use

⅛

” drill bit to start holes for the screws to attach the straps.

The door check straps stop the door from opening all the way up and scratching your paint. Test the
placement of the strap for door travel before final assembly.
Open the door wide but not enough so that the door hits the body. The straps will stretch slightly over
time so allow enough room for this by closing the door slightly from the maximum.
While holding the door open, pull the check strap tight and mark the location of the mount holes on the
inside face of the 2”x 2” tube.
Drill

3

/

16

” holes at the marked locations

Rivet the mount to the chassis.

Steering wheel center section



WD40,

5

/

32

” hex key



Steering wheel/hardware, Factory Five Badge

Unwrap the steering wheel center section and push it into the steering wheel and boss, a little WD40 on
the o-ring helps if it is tight.
Peel the backing off the badge and stick it in the center section making sure you are aligned with the top
of the steering wheel. If necessary, file any flashing off the bottom edge of the emblem so that it will fit.

«
...
374
375
376
377
378
...
»

Содержание Type 65 Coupe



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Type 65 Coupe

Бренд: GOgroove Страницы: 9

Camaro 12000 1968 Series

Бренд: Chevrolet Страницы: 455

Бренд: Yakima Страницы: 12

Бренд: Mercedes-Benz Страницы: 373

Бренд: Inbay Страницы: 20

Бренд: Kuda Страницы: 3

MCL-7000 Series

Бренд: Dakota Digital Страницы: 2

Бренд: Volvo Страницы: 284

Бренд: Volvo Страницы: 10

Бренд: Flash Cover Страницы: 2

Бренд: Porsche Страницы: 98

Бренд: KEKO Страницы: 13

Stealth 4191F Series

Бренд: Road Armor Страницы: 5

Бренд: A-Tach Mounts Страницы: 2

Бренд: J. Strong Страницы: 2

Бренд: Axxess Страницы: 16

Бренд: Aston Martin Страницы: 415

Бренд: Westin Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды