FABtotum Personal Fabricator Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 123

background image

FABtotum Complete Manual

www.fabtotum.com

| 3

SAFETY & WARRANTY GUIDELINES

Before we venture into uncharted territory, let’s make sure to cover safety basics of the FABtotum Personal Fabricator.
As a general rule, please operate according to the instructions provided by authorized sources only.

Follow the safety instructions below and use common safety practices. Always contact support for advice before modifying
or employing the machine in a way that could cause hazards.

FIRST SETUP AND PLACEMENT

Follow the first setup manual or the complete manual, available at fabtotum.com/support
Place the unit on stable, clean surfaces, away from any obstacles within 30cm / 12″ from the unit.
The unit is intended for indoor use only. Do not use or place outside.
The unit only operates with room temperatures between 15°C and 28°C.
Place unit far from sources of heat, humidity or cold air.
Keep clean dust and clear of any liquid.

IMPORTANT SAFETY NOTES:

Caution: main health risks come from the machine’s moving parts and the components that can heat up, such as the plane
and the modules.

These parts have warning stickers and status LEDs on them to inform of the dangers related to the use of the FABtotum.

Do not touch the nozzle, the heated bed or any moving part of the unit.

«
1
2
3
4
5
...
»

Содержание Personal Fabricator




























































































































Отзывы:

Нет отзывов

Похожие инструкции для Personal Fabricator

Бренд: DataCard Страницы: 8

Бренд: DataCard Страницы: 8

Бренд: DataCard Страницы: 3

Бренд: Unimark Страницы: 38

Бренд: BALCO Страницы: 24

Бренд: Xerox Страницы: 15

Бренд: Xerox Страницы: 9

DocuPrint 180 NPS Series

Бренд: Xerox Страницы: 172

Бренд: Xerox Страницы: 11

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 40

Color C75 Press

Бренд: Xerox Страницы: 340

DocuPrint N3225

Бренд: Xerox Страницы: 169

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 196

Бренд: Xerox Страницы: 108

Бренд: Xerox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды