FABtotum Personal Fabricator Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 123

background image

FABtotum Complete Manual

www.fabtotum.com

| 79

FILAMENT LOADING / UNLOADING

Loading the filament

Loading or changing the filament is an assisted procedure on the FABtotum. The user just need to follow the on-screen
instructions and perform a series of tasks to allow the unit to safely insert or remove the filament from the system.
The task is slightly different, depending on the version of the unit and installed Printing Head.
Please refer to the paragraph concerning each Head before proceeding.

IMPORTANT:
The correct Head must be installed using the FABUI Maintenance > Head Installation procedure before proceeding with
loading or unloading a spool.

Printing Head PRO

«
...
77
78
79
80
81
...
»

Содержание Personal Fabricator




























































































































Отзывы:

Нет отзывов

Похожие инструкции для Personal Fabricator

Бренд: Panasonic Страницы: 32

Бренд: Magicard Страницы: 30

Бренд: Magicard Страницы: 35

MAGICARD ID Card Printer

Бренд: Magicard Страницы: 30

Бренд: Magicard Страницы: 6

Бренд: Oki Страницы: 95

Бренд: Primera Страницы: 2

Бренд: TP Страницы: 10

mC-Print3 MCP31LB

Бренд: Star Страницы: 12

Бренд: ABLE Systems Страницы: 12

Бренд: Citizen Страницы: 32

Бренд: U-Line Страницы: 18

Бренд: BIXOLON Страницы: 20

Бренд: UnionTech Страницы: 44

Aficio SG 7100DN

Бренд: Ricoh Страницы: 359

Бренд: Brother Страницы: 81

HL-2400C Series

Бренд: Brother Страницы: 23

Бренд: Brother Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды