Faber Hemmet Brass Скачать руководство пользователя страница 9

Страница: 9 / 52

- 3 -

Battery Information.

1. Unclip the battery cover on the back of the remote

control. (See Fig. 7)

2. Install AAA batteries into the remote control.
3. Replace the battery cover.

Discard leaky batteries.

Dispose of batteries in the proper manner according to
provincial and local regulations.
Any battery may leak electrolyte if mixed with a diff erent
battery type, if inserted incorrectly, if all the batteries are
not replaced at the same time, if disposed of in a fi re, or if
an attempt is made to charge a battery not intended to be
recharged.

Thermal safety cut-out

A thermal safety cut-out is incorporated in the fan heater
to prevent damage due to overheating. This can happen if
the heat outlet was restricted in any way or if the chimney
fl ue has not been blocked off eff ectively. If the cut-out
operates, unplug the heater from the socket outlet and
allow approximately 10 minutes before reconnecting.
Before switching the heater back on remove any
obstruction that may be restricting the heat outlet, then
continue normal operation.

Tips for using your appliance.

1. Only pull out the drawer when its time to refi ll the

water tank or change a lamp, otherwise it may lead to
excess water in the sump and reduced fl ame eff ect.
If this happens empty the water from the sump as
instructed under ‘Maintenance’.

2. With the fl ame setting on minimum the unit will use

approximately 40ml of water per hour and will last
3 times as long than when it is at maximum fl ame
setting.

3. Do not tilt or move the fi re while there is water in the

tank or sump.

4. Make sure that the fi re is on a level fl oor.

5. The fl ame control knob ‘C’ Fig. 2 may be turned up or

down to give a more realistic eff ect.

6. Sometimes the fl ames appear more real when the fl ame

control knob is turned down.

7. Give the fl ame generator some time to react to

changes you may make on the fl ame control knob.

Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE

Changing lamps.

If a large amount of the smoke appears grey or colourless
it may be that one or more lamps have failed.
You can check for lamp failure as follows.
1. Leaving the fl ame eff ect on, gently pull the drawer fully

out by the tab. (See Fig. 3)

2. View the lamps from a distance in front of the fi re and

observe which lamp needs to be changed.

3. Put Switch ‘A’ in the ‘OFF’ position, and unplug the fi re

from the mains.

4. Leave the appliance for 20 minutes to allow the lamps

to cool down before removing them.

5. Remove the water tank by lifting upwards and place in

a sink.

6. Remove the sump as described in the Cleaning Section.
7. Remove the defective lamp, by gently lifting vertically

and disengaging the pins from the lamp holder, (See
Fig. 4 and 5). Replace with a Dimplex Opti-myst, 12V,
50W, Gu5.3 base, 8° beam angle, coloured lamp.
(Purchased from www.dimplex.co.uk under the section
‘After Sales Service’, details of how to purchase the
lamps are contained therein.)

8. Carefully insert the two pins of the new lamp into the

two holes in the lamp holder. Push fi rmly in place. (See
Fig. 4 and 5).

9. Replace the Sump and water tank and carefully close

the drawer.

10. Switch on.

Filling the water tank.

When the water tank is empty, fl ame and smoke eff ect
shuts off , and you will hear 2 audible ‘beeps’. Follow these
steps to refi ll:
1. Press Switch ‘A’ to

(0)

(See Fig. 2)

2. Gently pull out the drawer as far as possible by the tab.

(See Fig. 3)

3. Remove the water tank by lifting upwards and

outwards.

4. Place the water tank in sink and remove cap, Anti-

clockwise to open. (See Fig. 6)

5. Fill tank with

fi ltered tap water only

This is necessary

to prolong the life of the fl ame and smoke producing
unit.