Faber Hemmet Brass, Руководство пользователя

Страница: 10 / 52

- 4 -
Air fi lter.
1. Press Switch ‘A’ to the ‘OFF’
(0)
position (See Fig. 2)
2. Gently pull the drawer out as far as possible. (See Fig. 3)
3. Remove the tank and place in a sink with the cap facing
upwards.
4. Gently slide upwards the air fi lter plastic holder. (See
Fig. 17)
5. Remove the fi lter combination from the plastic holder.
6. Gently rinse with water in the sink and dry with fabric
towel before returning.
7. Replace the fi lter combination making sure that the
course black fi lter is in contact with the plastic holder.
(See Fig. 18)
8. Replace the tank.
9. Close the drawer fully.
10. Press Switch ‘A’ to the ‘ON’ (
I
) position (See Fig. 2)
Recycling.
For electrical products sold within the European
Community. At the end of the electrical
products useful life it should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your Local Authority
or retailer for recycling advice in your country.
After Sales Service.
Your product is guaranteed for one year from the date of
purchase. Within this period, we undertake to repair or
exchange this product free of charge (excluding lamps
& subject to availability) provided it has been installed
and operated in accordance with these instructions.
Should you require after sales service or should you need
to purchase any spares, please contact the retailer from
whom the appliance was purchased or contact the service
number relevant to your country on the warranty card.
Please do not return a faulty product to us in the fi rst
instance as this may result in the loss or damage and delay
in providing you with a satisfactory service.
Please retain your receipt as proof of purchase.
Cleaning.
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
We Recommend cleaning the following components once
every 2 weeks, particularly in hard water areas:-
Water Tank, Sump and Seal, Sump lid, Tank cap and seal,
Air fi lter.
For general cleaning use a soft clean duster – never use
abrasive cleaners. To remove any accumulation of dust or
fl uff the soft brush attachment of a vacuum cleaner should
occasionally be used to clean the outlet grille of the fan
heater.
Water tank
1. Remove water tank, as described earlier, put into sink
and empty water.
2. Using the supplied brush gently rub the inside surfaces
of the cap paying particular attention to the rubber
ring in the outer groove and the centre rubber seal.
3. Put a small quantity of washing up liquid into the tank,
refi t the cap and shake well, rinse out until all traces of
washing up liquid are gone.
4. Refi ll with fi ltered tap water only, replace the cap, do
not overtighten.
Sump
1. Press Switch ‘A’ to the ‘OFF’
(0)
position
2. Gently pull the drawer out as far as possible. (See Fig. 3)
3. Remove the water tank by lifting upwards.
4. Disconnect the electrical connector, located on the left
side of the sump, by fi rst loosening the two retaining
screws and gently withdrawing the connector. (See
Fig. 8)
5. Release the lower sump locking tabs by turning 90°,
this allows the sump to be lifted completely from its
location. (See Fig. 9)
6. Gently lift up the sump assembly, taking care to keep
level so as not to spill any water. Sit the assembly in the
sink. (See Fig. 10)
7. Release the two upper sump locking tabs by turning
90°, then lift off the sump lid. (See Fig. 11)
8. Carefully tilt, as shown, so that the liquid drains out of
the sump. (See Fig. 12)
9. Put a small amount of washing up liquid into the sump,
and using the supplied brush, gently clean all surfaces
including the metal discs and the rubber seal located
in the top grooved surface.
Do not remove the rubber
seals
. (See Fig. 13 and 14)
10. When cleaned, thoroughly rinse the sump with clean
water.
11. Clean the outlet surface of the sump lid with the brush
and fl ush out thoroughly with water. (See Fig. 15 & 16)
12. Reverse the above steps to reassemble.