Faber Cristal 24 SS, Инструкции по установке; Информация по использованию и уходу

Страница: 31 / 36

31
INFORMACIÓN DE USO Y CUIDADO
Para mejores resultados
Encienda la campana varios minutos antes de cocinar para desarrollar un flujo de aire adecuado. Deje
que la campana funcione durante varios minutos después de completar la cocción para eliminar todo
el humo y los olores de la cocina.
Version 07/11 - Page 7
Rangehood Control Panel
All controls are located on the right side of the rangehood.
Light On/Off Switch
TheOn/Off switch for the halogen light is located behind the
front trim. Moving the switch to the 1 Position turns the light
On. Moving the switch to the 0 position turns the light off.
Blower Speed Switch
B in FIGURE 10 shows the speed control switch for the
blower. Moving the switch to the 1 Position turns the blower
on LOW. Moving the switch to the 2 Position turns the blower
on MEDIUM. Moving the switch to the 3 Position turns the
blower on HIGH. Moving the switch to the 0 Position turns
the blower off.
Automatic Operation
As long as the blower and light switches are on, the blower
and light will automatically operate when the visor is opened
and shut off when the visor is closed.
For Best Results
Start the rangehood several minutes before cooking to develop
proper airflow. Allow the unit to operate for several minutes
after cooking is complete to clear all smoke and odors from
the kitchen.
Cleaning
The metal grease filters should be cleaned frequently in hot
detergent solution or placed in the dishwasher. Clean exterior
surfaces with hot soapy water, and use stainless steel cleaner
on the front strip. Using abrasives and scouring agents can
scratch rangehood finishes and should not be used to clean
finished surfaces.
FIGURE 10
FIGURE 7
FIGURE 8
Replacing the Halogen Lamps
Before attempting to replace the lamps, make sure that
the light switch is turned off. Remove the 2 screws (as
indicated in FIGURE 8) that hold the light support and
gently pull the support down from the hood. Remove
the lamp from the light support and replace with new
lamp. Replace the light support and fix it into place
with the 2 screws.
An alternative method to replace the lamps is to use a
1 1/4" suction cup ( FIGURE 9 ). Attach the suction cup
to the bulb and pull firmly down on the bulb and replace
with a new lamp. The hood uses a 20 Watt MR-11 type
halogen bulb with a lens cover.
FIGURE 9
EN
1
2
12
CARE
Grease filters
CLEANING METAL SELF- SUPPORTING GREASE FILTERS
• The filters must be cleaned every 2 months of operation, or
more frequently for particularly heavy usage, and can be
washed in a dishwasher.
• Remove the filters one at a time by pushing them towards the
back of the group and pulling up at the same time.
• Wash the filters, taking care not to bend them. Allow them to
dry before refitting.
• When refitting the filters, make sure that the handle is visible
on the outside.
Activated charcoal filter (Recirculating version)
These filters (not supplied with the rangehood)are not washable
and cannot be regenerated, and must be replaced approximately
every 4 months of operation, or more frequently with heavy us-
age.
REPLACING THE ACTIVATED CHARCOAL FILTER
• Remove the metal grease filters
• Remove the saturated activated charcoal filter as shown ( A ).
• Fit the new filters ( B ).z
• Replace the metal grease filters.
�
�
Lighting
LIGHT REPLACEMENT
20 W halogen light.
• Remove the 2 screws fixing the Lighting support, and pull it
out of from the Hood.
• Extract the lamp from the Support.
• Replace with another of the same type, making sure that the
two pins are properly inserted in the lamp holder socket holes.
• Replace the Support, fixing it in place with the two screws re-
moved as above.
EN
1
1
11
USE
Control board
L Light Switches the lighting system on and off.
M Motor Switches the extractor motor on and off.
V Speed Sets the operating speed of the extractor:
1. Low speed, used for a continuous and silent air change in the presence of
light cooking vapour.
2. Medium speed, suitable for most operating conditions given the optimum
treated air flow/noise level ratio.
3. Maximum speed, used for eliminating the highest cooking vapour emission,
including long periods.
�
�����
�
�
�
�
�
�
EN
1
2
12
CARE
Grease filter s
CLEA NING META LS ELF- SUP PORTI NG GREA SEFI LTE RS
•T he filte rsm ust bec lea ned eve ry 2m onthsof opera tion, or
mor ef reque ntlyf or partic ularly heav yus age , a ndc an be
wash edin ad ish wash er.
•Re mov ethe filte rsone at a time bypushing the mtow ards the
back of the group a ndpul ling u pat the sa me ti me.
•W ash thefilte rs,ta king care notto ben dth em .A llo wth em to
drybe fore refitting .
•W hen refitting thefilte rs,m ake sure that the hand leis visible
onth eo utside .
Activated charcoal filter (Recirculating ver sion)
The se filte rs(not supplie dw ithth era ngehood)a re not was hab le
and cannot be regenerat ed,a nd must be replaced appro xim atel y
eve ry 4m onthsof opera tion, orm ore fre quently with heav yus -
age.
REPLACING THE ACTIVAT EDCHA RCOAL FIL TER
•Re mov ethe meta l gre ase filte rs
•Re mov ethe satura ted activ ated cha rco al f iltera sshow n( A ).
•Fit t hene wfilte rs ( B ).z
•Rep lace them etal greas efilters .
�
�
Lighting
LIG HT REPLACEMENT
20 Whal oge nli ght .
•R em ove the2 scr ews fix ing theL igh tings uppor t, a nd pullit
outof fro m the Hoo d.
•Ex tract the lam pfr om theSupp ort.
•Rep lace with anot her of the samety pe, maki ng sure that the
two pins are prope rly ins erte d in the lam p holde r so cke t hole s.
•Rep lace the Supp ort, fixi ng iti np lace with the two screws re-
mov edas abov e.
GREASE FILTER REMOVAL
The grease filters are removed by pressing the handle on
the right side of the filter (FIGURE 7) . When replacing,
make sure that the filters are properly positioned with
the handles on the right and visible. There are 2 grease
filters, one in the slide out part of the hood, the other in
the back.
USE AND CARE INFORMATION
B
Panel de Control de la Campana
Todos los controles están ubicados en el lado derecho
de la campana.
Interruptor de encendido / apagado de luz
El interruptor de encendido / apagado de la luz se
encuentra detrás de la moldura frontal. Al mover el inter-
ruptor a la posición 1, se enciende la luz. Al mover el
interruptor a la posición 0, se apaga la luz.
Interruptor de velocidad del ventilador
B en la FIGURA 10 muestra el interruptor de control
de velocidad del ventilador. Al mover el interruptor a la
posición 1, el ventilador se enciende en BAJO. Al mover
el interruptor a la posición 2, el ventilador se enciende
en MEDIO. Al mover el interruptor a la posición 3, el
ventilador se enciende en ALTO. Al mover el interruptor
a la posición 0, el ventilador se APAGA.
Operación automática
Mientras el ventilador y los interruptores de luz estén
encendidos, el ventilador y la luz funcionarán automáti -
camente cuando se abra la visera y se apagan cuando
la visera se cierre.
Para mejores resultados
Encienda la campana varios minutos antes de cocinar
para desarrollar un flujo de aire adecuado. Deje que la
campana funcione durante varios minutos después de
que se complete la cocción para eliminar todo el humo y
los olores de la cocina.