![background image](http://html1.mh-extra.com/html/faac/daab-ep105/daab-ep105_instruction-manual_3113213018.webp)
INSTRUCTION MANUAL DAAB AUTOMATIC CONTROL UNIT EP105
18
Revision 3
Applications
This section describes the settings required for various types of application. Type of application should be indicated in
channel C700
• Folding doors
Load guard
When a folding door is commissioned, the load guard must be configured for personal protection. This means that it
provides protection during the opening movement according to the applicable standards (obstacles while opening and
also inside the folds). Personal protection means that a normal power is defined – the power used by the motor cannot
fall below a lower limit or exceed an upper limit, calculated automatically by the system on the basis of the normal power.
As a result, the load guard cannot be set higher than the normal effect, providing optimum protection during the opening
movement.
Safety edge
There are usually two safety edges for a folding door, one for each half. They are connected to SE.C1 and SE.C2 and
adjusted as described in the section on Safety edge. According to the factory settings, the safety edge inputs for opening
movement, SE.O1 and SE.O2, are disabled.
• Sliding doors/sliding gates
Load guard
When a sliding door/gate is installed, the load guard should be configured without personal protection. This means that
the purpose of the load guard is more to protect the motor and other mechanisms from damage. The load guard does not
therefore provide effective protection for the opening movement if the door is opened against an obstacle with a crush risk.
Safety edge
Up to two safety edges are used in a sliding door/gate – one at the front and possibly one at the back. More than one safety
edge is usually fitted to sliding gates to provide protection from crushing between the gate buffers and fixed objects like
gate posts, drive units, etc. The safety edges fitted to the front provide protection for the closing movement, and those fitted
to the back provide protection for the opening movement. Safety edges providing protection for the closing movement
are connected to SE.C1 and SE.C2, while SE.O1 and SE.O2 are for the opening movement. Adjust the safety edge as
described in the section on Safety edge. Note that according to the factory settings, the safety edge inputs for opening
movement, SE.O1 and SE.O2, are disabled.
• Up-and-over doors
Load guard
When an up-and-over door is installed, the load guard should be configured without personal protection. This means that
purpose of the load guard is more to protect the motor and other mechanisms from damage.
Safety edges
A safety edge for an up-and-over door must be set to send acknowledgements. This is a setting that is made in the EP105
by setting value 1 in channel C101 (C448 must be set to 0), safety edge acknowledgement. The safety edge is connected to
SE.C1 and adjusted as described in the section on Safety edge. Note that safety edge acknowledgement only works with
input SE.C1.
• Swing gates
Load guard
When a swing gate is installed, the load guard should be configured without personal protection. This means that purpose
of the load guard is more to protect the motor and other mechanisms from damage. The load guard does not therefore
provide effective protection for the opening movement if the gate is opened against an obstacle with a crush risk.
Safety edges
There are usually two safety edges for a hinged gate, one on each side. They are connected to SE.C1 and SE.C2 and
adjusted as described in "Safety edge". If no safety edge is used for the opening movement, SE.O1 and SE.O2 are disabled.
• Barriers
Load guard
Load guards on barriers are only intended to protect the barrier and other mechanical components, so they are configured
without personal protection. This means that the barrier changes direction in the presence of a high load in either direction.
Safety edge
A barrier usually has no safety edge at all – in this case, disable SE.C1, SE.C2, SE.O1 and SE.O2. Otherwise, adjust the
safety edge as described in "Safety edge".
Содержание DAAB EP105
Страница 1: ...INSTRUCTION MANUAL DAAB AUTOMATIC CONTROL UNIT EP105...
Страница 58: ...INSTRUCTION MANUAL DAAB AUTOMATIC CONTROL UNIT EP105 58 Revision 3 Notes...
Страница 59: ...INSTRUCTION MANUAL DAAB AUTOMATIC CONTROL UNIT EP105 59 Revision 3 Notes...
Страница 60: ...Revision 3 FAAC Nordic AB Box 125 SE 284 22 Perstorp 46 435 77 95 00 www faac se support faac se...