![background image](http://html1.mh-extra.com/html/faac/d700hs/d700hs_installation-manual_3133099009.webp)
8
ENGLISH
9. COURTESY LAMP
- The courtesy lamp stays ON for 2 minutes after the end of the
movement (cannot be modified).
10. CONNECTIONS
ATTENTION: Before performing any operation on the board
(connections, maintenance), always cut electric power.
- To avoid any electrical disturbance, use separate sheaths for
mains power supply, signals and accessories.
- The D700HS operator has a cable with two-pole plug for the
230 Vac power supply.
- To connect external commands, safety devices and signals,
open the relevant pre-cut part (Fig. 26 ref.
).
- To connect the safety edge (see par. 18.3.), open the relevant
pre-cut part (Fig. 26 ref.
)
- Perform the electrical connections referring to Fig. 28.
If the
STOP
input is not used, jumper connect the input
to the terminal
.
If no photocells are used, connect the
FSW
input to
the terminal
-TX FSW
.
Input status LEDs:
The condition with automated system stopped and at
rest is shown in bold for every input.
LD
Meaning
OFF
ON
1
OPEN input status
Not active
Active
2
STOP input status
Active
Not active
3
FSW input status
Safety devices
engaged
Safety devices not
engaged
11. PROGRAMMING
11.1. Board settings
Set the control board using the DS1 dip-switches, referring to
chapter 8.3 to obtain the requested operation.
To select the Opening/Closing speed, set the
dip-switch 3 of DS1, as indicated in chapter 8.3.
We recommend you to set the dip-switch 3 to ON.
11.2. Learning (SET UP)
During the learning procedure, the obstacle detection
device is not operating. The STOP command and the
closing safety devices (FSW) are instead active; their
operation stops the learning phase and signals a fault.
The SET UP cycle must be performed with mounted
cover. Just remove the rear door (Fig. 27). Seize with
both hands the rear door and gently draw downwards.
At the end of the procedure indicated in this chapter,
mount the door again.
The learning cycle enables you to define the following:
- necessary thrust to move the door.
- deceleration points.
- stop points at opening and closing.
- pause time (in automatic logic).
The learning phase must begin when the operator is blocked,
independently of the door position.
The procedure also determines the operating logic.
The logic tables indicate the behaviour of the automated
system in the different conditions and following to commands
or operation of the safety devices.
The learning phase can be performed in both automatic
or manual mode; in this latter case, you can determine the
deceleration points at opening and closing; in the automatic
mode, instead, the control board autonomously determines the
movement parameters.
If the procedure is not completed correctly (i.e. due to excessive
friction during door movement), the board signals the fault status
(the SET UP LED flashes slowly). In this case, after having removed
the cause, you need to repeat the procedure.
AUTOMATIC LEARNING WITH LOGIC “E” (SEMI-AUTOMATIC)
NOTE
: it is recommended to perform this
learning phase with
SLOW
speed.
(dip-switch
4
=
ON
)
Press the SET UP push-button for one second. (Fig. 36 ref.
)
The SET UP LED starts flashing as soon as the push-button is
released. (Fig.36 ref.
)
1) After 8 seconds, the operator automatically performs a
closing movement until reaching the stop point.(Fig. 37 ref.
)
2) The operator starts the opening movement. Wait for it to
reach the stop point or send an OPEN command (Fig. 38 ref.
) in the position where you want to stop the movement.
3) The operator closes the door again.
4) Wait for the door to reach the stop point and for the operator
to stop.
If the learning procedure has ended successfully, the SET UP LED
(Fig. 39 ref.
) stops flashing and stays ON for 5 seconds.
During these 5 seconds you can send OPEN pulses (Fig. 39 ref.
), in order to decrease the load on the release system,
within 2 seconds from each other to move the carriage back.
A pulse corresponds to a 5 millimetres stroke.
N.B.: The back movement of the carriage can only be seen
during the normal operation of the automated system.
The deceleration points are defined by the control unit.
MANUAL LEARNING WITH LOGIC “E” (SEMI-AUTOMATIC)
Press the SET UP push-button for one second. (Fig. 40 ref.
)
The SET UP LED starts flashing as soon as the push-button is
released. (Fig.40 ref.
)
Start the following procedure within 8 seconds (otherwise the
operator performs the automatic learning):
1) Send the 1st OPEN command: the operator performs a
decelerated closing movement until it detects the stop
point, then it stops.(Fig. 41 ref.
and Fig. 42 ref.
)
2) Send the 2
nd
OPEN command: the operator continues with
an opening movement. (Fig. 41 ref.
and Fig. 42 ref.
)
3) Send the 3
rd
OPEN command to define the point in which the
deceleration should start. (Fig. 41 ref.
and Fig. 42 ref.
)
4) Send the 4
th
OPEN command to define the opening stop
point, or wait for the automated system to detect the stop
point and to stop. (Fig. 41 ref.
and Fig. 42 ref.
)
5) Send the 5
th
OPEN command: the automated system starts
the closing movement. (Fig. 41 ref.
and Fig. 42 ref.
)
6) Send the 6
th
OPEN command to define the point in which the
deceleration should start. (Fig. 41 ref.
and Fig. 42 ref.
)
7) Wait for the door to reach the stop point and for the operator
to stop. (Fig. 42 ref.
)
Содержание D700HS
