![background image](http://html1.mh-extra.com/html/faac/d700hs/d700hs_installation-manual_3133099008.webp)
7
-24 V LAMP -TX FSW
FSW
STOP
+24 V
OPEN A
ENGLISH
8.4. Operating logics
Logic A (automatic)
Logic E (semi-automatic)
Status
Open (pulse)
Stop
Fsw
CLOSED
Opens and closes
again after pause time
No effect (2)
No effect
OPENING
No effect
Blocks (2)
No effect (1)
OPEN IN
PAUSE
Restarts pause time
count (1)
Blocks (1)
Restarts pause time
count (1)
CLOSING
Reverses movement
Blocks (2)
Reverses movement
BLOCKED
Closes
No effect (2)
No effect (1)
Status
Open (pulse)
Stop
Fsw
CLOSED
Opens
No effect (2)
No effect
OPENING
Blocks
Blocks (2)
No effect (1)
OPEN
Closes
No effect (2)
No effect (1)
CLOSING
Reverses movement
Blocks (2)
Reverses movement
BLOCKED
Closes
No effect (2)
No effect (1)
Fail Safe
If activated, it enables the test on the photocell operation before
every movement.
Anti-crushing sensitivity
In the event of irregular movement of the doors, it enables
to reduce the sensitivity of the anti-crushing device to avoid
unwanted operations.
8.2. Terminal boards and connectors
8.3. DS1 Programming dip-switches
Description
Connected device
OPEN A
Control device with NO contact
(see chapter OPERATING LOGICS)
STOP
Device with NC contact, that causes the block of the
automated system
Negative for OPEN A and STOP devices
FSW
Closing safety device with NC contact
(see chapter OPERATING LOGICS)
LAMP
OPEN COLLECTOR output, 24 Vdc 100 mA.,
for flashing lamp
-TX FSW
Safety accessory power supply negative
(FAIL SAFE function)
Accessory power supply negative
+24 Vdc accessory power supply
No. function
OFF
ON
1 Fail Safe
Active
Not active
2 Anti-crushing sensitivity
Low
High
3
Opening/Closing speed
Same
Closing at
reduced
speed
4 Carriage speed
High
Low
(1) With maintained pulse, it inhibits closure.
(2) With maintained pulse, it inhibits closure and/or
opening.
During the opening movement, the intervention
of the anti-crushing device causes immediate
stop. During the closing movement, it re-opens
the
door.
If an obstacle is detected at closure in the same
position for three consecutive times, the automated
system considers this position as the new closing
stop point and changes over to closed status. To
restore the correct positions, remove the obstacle
and command a new cycle: on next closure, the
automated system moves at decelerated speed
until it locates the stop point.
Содержание D700HS
