manualshive.com logo in svg
background image

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Limited Warranty 

 

To the original purchaser only:

 FAAC International, Inc., warrants, for twenty-four (24) months from the date of 

invoice, the gate operator systems and other related systems and equipment manufactured by FAAC S.p.A. and distributed by 
FAAC International, Inc., to be free from defects in material and workmanship under normal use and service for which it was 
intended 

provided

 it has been properly installed and operated. FAAC International, Inc.'s obligations under this warranty shall be 

limited to the repair or exchange of any part of parts manufactured by FAAC S.p.A. and distributed by FAAC International, Inc. 
Defective products must be returned to FAAC International, Inc., freight prepaid by purchaser, within the warranty period. Items 
returned will be repaired or replaced, at FAAC International, Inc.'s option, upon an examination of the product by FAAC 
International, Inc., which discloses, to the satisfaction of FAAC International, Inc., that the item is defective. FAAC International, 
Inc. will return the warranted item freight prepaid. The products manufactured by FAAC S.p.A. and distributed by FAAC 
International, Inc., are not warranted to meet the specific requirements, if any, of safety codes of any particular state, municipality, 
or other jurisdiction, and neither FAAC S.p.A. or FAAC International, Inc., assume any risk or liability whatsoever resulting from 
the use thereof, whether used singly or in combination with other machines or apparatus. 
 

Any products and parts not manufactured by FAAC S.p.A. and distributed by FAAC International, Inc., will carry 

only the warranty, if any, of the manufacturer. This warranty shall not apply to any products or parts thereof which have been 
repaired or altered, without FAAC International, Inc.'s written consent, outside of FAAC International, Inc.'s workshop, or altered in 
any way so as, in the judgment of FAAC International, Inc., to affect adversely the stability or reliability of the product(s) or has 
been subject to misuse, negligence, or accident, or has not been operated in accordance with FAAC International, Inc.'s or FAAC 
S.p.A.'s instructions or has been operated under conditions more severe than, or otherwise exceeding, those set forth in the 
specifications for such product(s). Neither FAAC S.p.A. or FAAC International, Inc., shall be liable for any loss or damage 
whatsoever resulting, directly or indirectly, from the use or loss of use of the product(s). Without limiting the foregoing, this 
exclusion from liability embraces a purchaser's expenses for downtime or for making up downtime, damages for which the 
purchaser may be liable to other persons, damages to property, and injury to or death of any persons. Neither FAAC S.p.A. or 
FAAC International, Inc., assumes nor authorizes any person to assume for them any other liability in connection with the sale or 
use of the products of FAAC S.p.A. or FAAC International, Inc. The warranty hereinabove set forth shall not be deemed to cover 
maintenance parts, including, but not limited to, hydraulic oil, filters, or the like. No agreement to replace or repair shall constitute 
an admission by FAAC S.p.A. or FAAC International, Inc., of any legal responsibility to effect such replacement, to make such 
repair, or otherwise. This limited warranty extends only to wholesale customers who buy directly through FAAC International, 
Inc.'s normal distribution channels. FAAC International, Inc., does not warrant its products to end consumers. Consumers must 
inquire from their selling dealer as to the nature and extent of that dealer's warranty, if any. 

 

This warranty is expressly in lieu of all other warranties expressed or implied including the warranties of 

merchantability and fitness for use. This warranty shall not apply to products or any part thereof which have been subject 
to accident, negligence, alteration, abuse, or misuse or if damage was due to improper installation or use of improper power 
source, or if damage was caused by fire, flood, lightning, electrical power surge, explosion, wind storm, hail, aircraft or 
vehicles, vandalism, riot or civil commotion, or acts of God. 

 

 

FAAC International, Inc. 

303 Lexington Avenue 

Cheyenne, WY  82007 

 
 

844 IM, 6/98

 

Upswung.com

Содержание 844
























Отзывы: