manualshive.com logo in svg

FAAC 844, Руководство по установке

Поделиться
Скачать
FAAC 844 Скачать руководство пользователя страница 5

 

5 

Unpacking the Operator 

Complete the following steps to unpack the operator. 
 
1.  Before you remove the operator from the carton, 

check for any physical shipping damage, such as a 
torn shipping carton or leaking oil. Inspect the 
operator carefully after removing it from the 
carton. Notify the carrier immediately if you note 
any damage because the carrier must witness the 
damage before you can file a claim. 

 
2.  As you unpack the operator, insure that all parts 

are included. The package should contain all the 
items listed in the Parts List for your particular 
operator. 

Parts List 

1 844 

Operator 

1  Electronic control panel (either the 844 MPS or 

the 844 B/C, whichever you ordered, is installed 
inside the operator) 

1  Hardware package that contains the following: 

1  Black triangular cover key 

1  Manual Release key 
2  Limit switch plates, each measures 2-1/8 

× 

3-1/2 in. (54 

×

 89 mm)  

1  Heavier clutch spring for a gate leaf weighing 

2200 lb (1000 kg) or more 

1  Grounding connector, nut, and washer 
3  Covers for wiring access holes inside the 

operator 

If you have ordered a chain version of the 844 
Operator, you also have 1 chain kit with the following 
items: 

2  Limit switch plates to be mounted on the 

chain 

4 6-32 

×

 1 in. pan head screw with nuts 

4 10 

mm 

×

 30 mm cap screws with flat 

washers, lock washers, and nuts 

2  Operator fixing squares 
1 Chain 

guard 

1  5 mm bolt with flat washer 

 

1  Mounting angle bars 

8 Capacitor 

(35 

µ

F) 

2  Pinion or chain guard 

9  Clutch screw 

3  Inductive limit switch sensor 

10  Cap covering the hole for filling oil 

4  Housing for 3 spare fuses 

11  Key hole for the cover lock 

5  Operator cover that opens on hinges 

12  Grounding lug for the 844 Operator 

6  Control panel (the 844 MPS is shown here) 

13  Three bored holes for wiring cables 

7  Vent screw (on the gate side of the operator) 

14  Old style Manual Release (see Fig. 2 for new style) 

Figure 1. The main components of the 844 Operator 

Upswung.com

Содержание 844
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды