F.u.n.k.e. TRT800H-OLED Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 50

background image

TRT800H / P/N 800ATC-H-(2xx)-(2xx)

Operation and Installation

34

Document-No: 03.2124.010.71e / Revision: 2.10

4.4.2 Option Remote Header

The  transponder  provides    a  TRT800RT  remote  control  interface.  If  a
remote  header  TRT800RT  is  connected  transponder  can  be  remote
controlled  via  this  interface.  Remote  interface  provides  control  of  all
standard  user  inputs  available  during  standard  operational  mode.  For
more  information  see  TRT800RT  manual.  Remote  control  interface  de-
/activation  is  setup  configurable.  Remote  control  interface  must  only  be
connected to TRT800RT.

4.4.3 Serial Interface (RS232)

Using serial interface a GPS receiver can be connected to broadcast
own position via ADS-B Out position message. Position could be
received by other appropriately equipped aircrafts and processed for
collision avoidance ADS-B Out functionality.

The ADS-B function of this device has not been evaluated
during the FAA TSO certification process other than to
ensure non-interference. Due to the SW assurance of DAL
"D", the ADS-B function cannot be used in the US National
Airspace.

Connecting a GPS source will not comply to FAA
certification requirements with regard to ADS-B.

Supported formats/protocols are:

Option

Description

Baud rate

FREEFLIGHT GPS/WAAS Sensor 1201

NexNav NNL 3101

19200

AR-NAV

Bendix King
KLN 89B, KLN 94:

“Standard RS232

Sentence”,
KMD 150:

“Sentence Type 1”

Garmin 400 Series:

“Sentence Type 1”

(with and without altitude data)

9600

NMEA

NMEA-Format, data format RMC is
expected.

4800

Setup

→4.5.4 Wiring→3.7.3

Setup

→4.5.4 Wiring→3.7.3

«
...
33
34
35
36
37
...
»

Содержание TRT800H-OLED



















































Отзывы:

Нет отзывов

Похожие инструкции для TRT800H-OLED

Бренд: Galaxy Страницы: 38

Бренд: Kompernass Страницы: 3

Бренд: Destination Audio Страницы: 12

Бренд: EBENCH Страницы: 10

Бренд: Comtex Страницы: 24

Бренд: Raymarine Страницы: 38

Бренд: Curtis Страницы: 3

Бренд: Raymarine Страницы: 68

Бренд: Mitsubishi Electric Страницы: 31

Schottky Barrier Diodes MA6X718 (MA718)

Бренд: Panasonic Страницы: 3

Schottky Barrier Diodes MA2Z785 (MA785)

Бренд: Panasonic Страницы: 3

Transistors 2SB1218A

Бренд: Panasonic Страницы: 4

Schottky Barrier Diodes MA3S795EG

Бренд: Panasonic Страницы: 4

Schottky Barrier Diodes MA2SD290G

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды