F.u.n.k.e. TRT800H-OLED Скачать руководство пользователя

Страница: 38 / 50

TRT800H / P/N 800ATC-H-(2xx)-(2xx)

Operation and Installation

Document-No: 03.2124.010.71e / Revision: 2.10

4.5.2 Transponder configuration/record structure

Aircraft related parts of transponder configuration are stored in one out of
eight possible records (record=presetting). Each record contains the
following information:



Aircraft Address (AA, 24bit)



Aircraft category (AC)



Flight identification (FID, 6-8 numbers/letters)



RS-232 Interface setting (eg. GPS protocol)



Ground-Switch setting (Installed Yes/No)



Speed category (RI) of the respective aircraft



Remote Header setting (Installed Yes/No)

User related settings (e.g. squawk codes, display brightness) are stored
once in one global record (transponder internally) .

4.5.3 Transponder configuration/record handling

At least one record is stored in external memory. Up to 8 records can be
additional be applied during setup process.

If more than one record is applied, the active record must be selected out
of a list (determined by FID) during start-up of the transponder.

Previously applied records can be deleted again by filling

FID with zero’s

only.

4.5.4 General Setup

Any menu item can be passed by

MODE

. If no changes

are made the original settings will remain stored.
Modification of one menu item does not impact the others.
No entries will be deleted.

Содержание TRT800H-OLED



















































Результаты поиска

Содержание TRT800H-OLED

Отзывы:

Похожие инструкции для TRT800H-OLED

Бренды по названию

Популярные бренды

F.u.n.k.e. TRT800H-OLED, Эксплуатация и установка

Результаты поиска

Содержание TRT800H-OLED

Отзывы:

Похожие инструкции для TRT800H-OLED

Бренды по названию

Популярные бренды